To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5641 (+10)
  Choosing a shaft encoder?
 
As a neophyte robot builder and HandBoard user, may I ask for help in choosing the best shaft encoder? What vendor/supplier should I use? The current project is a very simple robot with a goal of accurate navigation. Thanks! (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  When people answer a question, I would like to broaden my knowledge as well.
 
Please either carbon copy your solutions to me, or the HB mailing list. I see a lot of good questions, but only a very few peoples responses. Thank you, (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  CyberMaster memory limit?
 
I've been playing around with programming the CyberMaster unit with NQC. I've noted that when the size of the program gets too large, the execution of the program fails in some way. The way it fails is sometimes somewhat inconsistent. I don't know (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: How to use the addition analog port ?
 
You can time share both your digital and your analog so long as your signal update speeds are not critical. Use a 4 to 8 demultiplexing chip for 4 of your digital I/O and an 8 to 4 multiplexer for the other 4. This effectively provides 8 digital (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Worm Drive Question
 
(...) This is an excellent solution for travel up to 7 inches or so, with a couple of minor drawbacks. 1) This part doesn't seem to be in production any more. I got a few copies, courtesy of Bill Katz, but had to trade away one joint of my little (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) Nope, not me. I never cut on purpose, and anything that breaks gets tossed. (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) tend to slide on the axle over time? (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Choosing a shaft encoder?
 
(...) I've had good results using the Hall-effect magnetic sensors that Patrick Hui sent with my HandyBoard. I glued magnets into three of the six holes in a Lego pulley wheel and glued the sensor into a small Lego brick. I don't know the part (...) (28 years ago, 28-Nov-98, to lugnet.robotics.handyboard)
 
  Re: CyberMaster memory limit?
 
Your program generates a .RCX file of 440 bytes. I've created one with 452 that works OK, but had to stop around that number because after more 2 or 3 lines of code the last task simply disappeared (my program had 1 main plus 3 tasks). I guess the (...) (28 years ago, 28-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
Try a little white glue. The glue helps prevent slippage and can be easily removed with warm water. Another option is a low-temperature "hot" glue gun. Many of the "hot" glue gun glues can be removed with vinegar. Use these at your own risk. matt (...) (28 years ago, 28-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR