To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5541 (+20)
  RE: legOS
 
(...) For some Pilot <--> RCX information take a look at (URL) if you haven't yet. This honestly is quite lagging on progress, but I _have_ been working on it in my very limited spare time. Hopefully within a week or two I'll have some much more (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
(...) Sorry I Lost you there, what do you mean by cut Lego? Tim (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) I mean cut threads (like on a screw) into the axel using a thread cutting tool (part of a tap and die set available at most good hardware stores). Check out (URL) near the bottom of the page. (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
(...) As in run an axle through a die to give it a thread, then put nylon bolts on it. Couldn't you just get some threaded rod, and spare your Lego (and avoid heresy :) ? Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: legOS
 
Has anyone be able to unpack the LegOS file. I have the CYGNUS GCC on my Wintel system. Using GZIP I get this error "Invaled Compressed Data - Format Violation" I would like to try out LegOS and see if it will allow memory storage/retrieval. I have (...) (28 years ago, 24-Nov-98, to lugnet.robotics)
 
  Re: legOS
 
(...) Hi, You can get legOS at (URL) . There is a note that some people have a problem with the file after downloading. Instead of clicking on the file, right click and select save link. It will save as legOS-0.1.2.tgz . Then run tar -xzf (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) lurk mode off - Yup ... unless you wanted to connect another cross-axle compatable element. I was just curious how well this would work as a substitute as I only had two original LEGO threaded axles from 8094. Heresy? Doesn't everyone have (...) (28 years ago, 24-Nov-98, to lugnet.robotics)
 
  Re: Re Sorry
 
In article <slrn75mnst.n02.matt...a.bu.edu>, Matthew Miller <lugnet.robotics@lugnet.com> quotes and writes (...) I think that you have hit the nail on the head there. I have read many articles on netiquette, and without exception they _all_ say (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Working automatic transmission!
 
I took Dave Forrest's automatic transmission challenge and built a working model out of basic technic. It determines which gear to use strictly based on the load being driven. I put a shock-absorber spring over an axle next to a screw. The screw (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: Sharp IR-Distance Sensor GP2D02
 
Hi Rajbala, in germany i can get this sensor from "Conrad Electronic". The Sensor is produced from Sharp. It is a very interesting sensor, because it is cheap (ca. 16,00$) It is possible to measure distances between 8-80cm, with a accuracy from (...) (28 years ago, 25-Nov-98, to lugnet.robotics.handyboard)
 
  micro-mouse
 
Hi! Can anyone tell me what are the registers that I have to initialise for a microcontroller before I start to write a program? Thank you. Chin (28 years ago, 25-Nov-98, to lugnet.robotics.handyboard)
 
  Re: legOS
 
(...) The only snags with legOS at the moment (that I'm aware of) are: a) You have to pull a battery out to clear the RAM b) It seems to have a problem with corrupting itself somewhere that I can't work out, and so far nor has Markus. It only shows (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: RCX Bytecode compiler in Tcl
 
Let me correct myself here. I did end up using some of Laurent's communications code in the bytecode compiler, after having experimented with some different approaches. Honestly, I simply forgot to track down and credit the source, which is no (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  (canceled)
 
 
  Any robotics clubs/enthusiasts in NJ?
 
Are there are robotics clubs in NJ or enthusiasts that might like to get together to discuss hobby robotics? Yours, John Oliva jlo@netlabs.net (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  German Robotic User
 
Hi all, i want to establish a German-Robotic-Group. Are there any german robotic users are interesting in this? I´m building sumo-roboters. You need more informations? Please mail bye bernd klein P.S. It is possible i will not answer during the next (...) (28 years ago, 25-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Working automatic transmission!
 
Andrew Carol writes: > * <- Large gear on differential body drives output. > *-R[]-* <- R = ratchet, [] = differential > ^ <- 1st gear axle has lg gear which drives med gear as > differential input 1. > ^ <- 2nd gear axle has med gear which drives (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
(...) Sure, you can do this with puppies, too! Ick, shudder! ("Arthur, Arthur, come quick! Someone's knurled the cat!" - hypothetical Monty Python skit) stephen (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: legOS
 
I have downloaded OK and since it is both tared and zip, you hve to first unzip it using "GZIP". GZIP is like Compress. Gzip (compress) -d legOS-0_1_2.tgz - uncompress the file tar -xzf legOS-0_1_2.t unarchive it. I am getting the error when I try (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: legOS
 
(...) Hi, When you run tar with the -xzf parameters, it first ungzips it then it untars it, all in the one command. The "z" is for gzip. The "x" is for extract the tar file. The "f" specifies the file. , __ _ _ , /|/ \o | | | | /| | | __/ | | | | (...) (28 years ago, 25-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR