 | | RE: Sony IR decoding routine!
|
|
I'm having trouble getting sony-ir.icb to load. Every time I try, I get the following error message: FATAL INTERNAL ERROR: ILLEGAL LINE IN .s19 FILE I've re-downloaded and installed both the sony-ir.icb and pcode_hb.s19 files but continure to get (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC serial hog?
|
|
Is there any way for my IC program to use the serial port? I am guessing the answer is no, as IC needs it for communicationg to the host computer. (Mac in my case.) So then the question becomes, is it possible to modify IC so that I can use the (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Sony IR decoding routine!
|
|
ic is very sensitive to linefeed termination in icb files. if you are runnnin on an ms-dos system, i believe it requires unix style (e.g., ctrl-j) termination, rather than ms-dos ctrl-m ctrl-j style. try removing the ctrl-m's from your copy of the (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: IC serial hog?
|
|
yes, it is possible for an ic program to use the serial port. see randy's instructions at (URL) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Can't initialize CONFIG register
|
|
In your message you said: (...) ok. the dlm *is* trying to write the one byte, because the config reg lives at 0x103f. and it's trying to write it as 0x0c, which is also correct. but apparently it is not working, b/c you say that when you run the (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Porting as11_ic to mac
|
|
IC users, I was thinking of perhaps porting as11_ic to the mac and I think I understand exactly what is going on in the unix script except for one thing. What is the C preprocessor doing? Is the only purpose of the C preprocessor to declare the two (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Porting as11_ic to mac
|
|
In your message you said: (...) all right dave! this wpuld be a great service to the mac community. the answer: yes, that is all the c precprocc is doing, generating 2 calls to the as11. it assembles the user pgm at two diff points in mem so that ic (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Quad encoders = the code
|
|
I have been successful in coding the Quad encoders. You will find below: - The source for the asm file - The source for the C file - the ICB file Thanks to the assembler on the web. I tried to use some of the Macintosh tools from the 68hc11 MIT FTP. (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | handy board crisis!
|
|
Well, let's see. I was rewiring my handy board so that it would run on 9.6V again, and everything seemed to be going fine. I soldered the pack back on with no problems, and was screwing the board onto its case when something horrible happened. The (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | handy board crisis II - read this!
|
|
Now THIS is weird. The battery light status seems to depend on the light going to the Sharp IR sensor now!!! If I expose it to light, the battery light turns on. If it's dark, it turns off. Modulated IR light makes the batt light flash. Have I (...) (29 years ago, 12-Feb-96, to lugnet.robotics.handyboard)
|
