 | | Re: Sonar Sensor Problems
|
|
michael lang kee wrote: <snip> (...) An occasional sporadic reading is normal and can best be handled by returning the median of three readings. Very noisy sonar data like yours might be attributable to noisy power to the board, a weak connection, (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Voltage for the DC motor
|
|
HI, Currently, I'm using 2 dc motors to drive my robot. The voltage of the motor is 12v rated. and the rated current is 300mA. These motors are directly plug into the HD for use. As a result, the robot cannot travelled fast and sometimes halt (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Implementation question
|
|
Hi All! I'm having exactly the same problem! The download seem to work correctly but after switching off and on the board again it seem not to start over. I have momentarily used another reset device. I dont know exactly the specification but it (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Motor output
|
|
Hi! When I work with the motor outputs, I found that the outputs are not linear. The "motor(m,p)" changes the output only in an increment 10 of p. Is there anyway I can get a more presiced output? Thanks. Keith (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Motor output
|
|
(...) The motor controls in the Handy Board library supports only 8 levels of power. Upgrade! Get the Smooth PWM version made by Julian Skidmore in the software contributed page on the Handy board web site ((URL) will have to do multiple things: 1- (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | HB woes
|
|
I'd appreciate mucho any help and ideas you all have I am building my HB, finally got the caps and crystal osc. working, and ran the HBDL program to download. All good and fine. I go off and solder in the transparent latch, and while doing so I (...) (28 years ago, 28-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Controling LEGO trains via Decta Control Lab
|
|
Hi All, I have been working on controlling LEGO trains thru the Decta Control Lab and I got a tip to pulse the power to the rails to better control the trains speed. There are 8 power settings via the ctrl lab and there are really only 2 or 3 (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Mindstorms A/D, 8 bit or 10 ?
|
|
OK, I just got a Mindstorms this yesterday and I've been surfing the various web pages about it (Lots of good info!) and I came across something odd. The specs for the microprocessor say it has 8 bit A/D's (Analog to digital converters), but the raw (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Other LCDs
|
|
Drew I picked up a 20x4 LCD from B. G. Micro (see their on-line catalog at (URL) and view page 2 - the LCD is the one in the upper right at $8.95, part number LCD1002). For 2x16, it will work just plugging into the HB. I poked memory locations (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | IR Detection
|
|
Hi Everyone: I am trying out the infra red emission and detection with the Handy Board. I have succeeded in the emission part but the detection circuit is not working. I know that the emitter LED is fine , with the help of Radio Shack Infrared (...) (28 years ago, 29-Oct-98, to lugnet.robotics.handyboard)
|