 | | RE: waterproof seals (a bit OT)
|
|
You could do what they do for aquarium filter pumps -- use magnetic transfer. Put a bar type magnet on the motor shaft and put a similar magnet on a propeller just outside the hull where the motor is. Since propellers require low-torque it works (...) (28 years ago, 16-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | IC installation problem
|
|
Dear Sir, Iam getting started with my project. At our lab we are having freeware version of IC (version 2.8). We tried to install the commercial version 3.2, but we are facing some problems. We tried to install from the site you told i.e (URL) you (...) (28 years ago, 16-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | serial board
|
|
I'm having trouble assembling the serial board. When I do the test(see snip below) I only get about 5 volts. When I try and run the downloader, I don't see the green light come on. (tried two different computers....) any suggestions? thanks in (...) (28 years ago, 16-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: new lego robotics mail alias
|
|
just what we need, another mailing list to keep up with! (28 years ago, 16-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Lego Plotter - a few pics.
|
|
Martyn Boogaarts wrote in message ... (...) Center - (...) plotter.jpg (...) includes: sorce code (basic pascal C++), Ldraw files and discriptions (...) Thanks for the response - Nice pics I was thinking about doing some Pneumatic related stuff - (...) (28 years ago, 17-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Lego Plotter - a few pics.
|
|
Martyn Boogaarts wrote in message ... (...) hmm, with a leg configuration like this - how would you handle Turning. I was thinking about the brute force method of one motor for lego motions and two for just picking the whole assembly up and (...) (28 years ago, 17-Oct-98, to lugnet.robotics)
|
| |
 | | RE: waterproof seals (a bit OT)
|
|
Mathew, I dont know if they would handle 103 psi but the drive shafts used in RC boats are sealed where they go through the bottom of the boat. If you put your motor in a sealed enclosure with the shaft coming into the enclosure you may be able to (...) (28 years ago, 17-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | File Types
|
|
Hello, I need help with the file types used by the handyboard. There are c, asm, icb, and lis files. How do I work with them? For example, I downloaded the compass.icb and compass.c files from the HandyBoard Site. Do I need to download both of them (...) (28 years ago, 17-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: File Types
|
|
Hi, load compass.icb first then compass.c at the ic prompt type v2x(); compass will display heading on the lcd. I'll send you the code I am using. hope this helps. Terry Gathright ---...--- (...) icb, (...) work? I (...) to do (...) understand (...) (...) (28 years ago, 17-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Rcvd my pneumatic components yesterday ... and am having doubts about their practicality. The smaller cylinder and pump (5116 & 5117) are not powerful enough to do much of amything of any use. The larger set (5107 & 5108) have enough power to lift (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|