To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *43159 (-10)
  Re: Basic NQC Problem
 
(...) There's a couple of ways to fix it. One is as Raplph said - have the first task start up a dedicated second task that does nothing more than look for a touch in a very tight loop. Very roughly, it would work something like this: task (...) (21 years ago, 13-Nov-05, to lugnet.robotics)
 
  Re: pre-releases brickos-0.9.0/lnpd-0.9.0 avail. for testing/feedback
 
Hi, I'm having problems getting dllx to work. I expanded the lnpd 0.9.0 zip file from sourceforge. I did ./configure and make with no problems or error messages. Now, I run lnpd with "lnpd --nolock". Then I do "dllx test.lx" and the green light on (...) (21 years ago, 13-Nov-05, to lugnet.robotics.rcx.legos)
 
  Re: Basic NQC Problem
 
(...) Big place to ask your questions here. I'll try to answer it, best i can. (...) You should switch of the motors and StopAllTasks in the check_sensor() task, if the bumper is hit. The main task does not furthermore look like that algorithmic as (...) (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Control Lab Connection help
 
Greetings, I have been trying program Control Lab using robolab. However, when I go to download all I get is the "Start CLI-1" window with a red 'X' through the reconnect icon. I am using the Control Lab interface start icon. I have tried several (...) (21 years ago, 12-Nov-05, to lugnet.robotics, lugnet.dacta)
 
  Re: Is it possible for a robot to count studs?
 
(...) Yes. The rotation sensor does occasionaly mess up at low rotation speeds, but this issue can be overcome by gearing up the actual rotation to higher speeds, and then dividing it back down in software. Kev (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Re: Is it possible for a robot to count studs?
 
(...) If you are moving slow enough, one possibility is using black friction pegs on a technic beam, say, one every other hole, and a touch sensor that moves by them counting them. If timing isn't enough to get you 1 +/- 0.1 stud resolution between (...) (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Re: Is it possible for a robot to count studs?
 
"Steve Lane yahoo.co.uk>" <stevenrobertlane@<n...pamplease> wrote in message news:IptF5D.vJD@lugnet.com... (...) Is there a way to do it without a rotation sensor? I wasn't planning on a LEGO order from S@H until after the New Year. The other (...) (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Re: Is it possible for a robot to count studs?
 
(...) I've used gear racks for this purpose. 2.5 gear rack teeth = 1 stud. Combine with a gear and a rotation sensor and away you go. (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Is it possible for a robot to count studs?
 
I'm wondering if anyone out there has ever tried to use a robot to count studs EG on a baseplate in order to make precise, stud-sized movements, for example, when making a pattern out of bricks or plates. If so, how did you do it, and can it be made (...) (21 years ago, 11-Nov-05, to lugnet.robotics)
 
  Re: New MOC - Big Wheel
 
(...) Great job Dave! I especially like the front bumpers design. Don't you experience too much friction on the wheels? When I built this (URL) it was a problem (rapid battery drain). Philo (21 years ago, 10-Nov-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR