 | | Re: New technique: three position piston control
|
|
In lugnet.technic, Kevin L. Clague wrote: (SNIP) (...) Sadly not, though I'll upload a lot more to my Brickshelf once my digital camera arrives. That will be better than circuits for explaining the positions of offset switches. I had also planned to (...) (21 years ago, 30-Sep-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Studless version of feed hopper - need help.
|
|
(...) Neat. But the images are too large for me to view (dial-up connection). Any chance of some (much) smaller pics? (...) I'm not sure. My first hopper (and still one that feeds well) is studless, using the smooth side of a series of studless (...) (21 years ago, 30-Sep-05, to lugnet.robotics)
|
| |
 | | Studless version of feed hopper - need help.
|
|
Below are 5 pics of a studless version of a feed hopper I've been working on with some Technic elements out of 8436. But I have a slight problem which I need some advice on the best way to fix. The hopper itself is made up of some Technic LiftArm (...) (21 years ago, 30-Sep-05, to lugnet.robotics)
|
| |
 | | Re: error in using brickOS under Bricx Command Center
|
|
(...) Can you do F12 and post the contents (if any)? Do you have bash installed? While the error message is displayed you can open a command prompt and change directory to the location of your source code file. There you should find a .cmd and a (...) (21 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Latest version BrixCC
|
|
(...) I have not yet made an official 3.3.7.9 release of BricxCC. My apologies for the delay. For now you can use the latest version in swan_test.zip. John Hansen (21 years ago, 29-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) With that limitation we'd be creating a register (or Turing) machine simulator, too. It would be interesting to see a real-world processor that only has increment and decrement instructions. I'm thinking the LEGO firmware doesn't support these (...) (21 years ago, 29-Sep-05, to lugnet.robotics, FTX)
|
| |
 | | Re: ROBOLAB Questions
|
|
Andrew, To the best of my knowledge the wait commands never turn off any motors. To do so would require that you could attach a motor modifier to the command. It would also limit the commands usefulness. If you really want a wait for distance (...) (21 years ago, 29-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Can't upload new program after I have used LNP under brickos
|
|
(...) Well, thanks for the help, that didn't actually work. But I found it out, what was my fault. In my Program I changed the LNP Base adress of the robot. After that the robot did not react to the default adress 0. So, at the end of the program I (...) (21 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: New technique: three position piston control
|
|
(...) <snip> I used some axle joints to optimise cylinder position limiting in normal logic (...) Do you have a website where I can peruse your work? (...) (21 years ago, 28-Sep-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: New technique: three position piston control
|
|
(...) No, I was so busy at work that I missed a couple of days online! I had a look at both, but a dual piston scheme works better for steering because of equalising the piston area and pushing at least 3 switches. In fact I have two cylinders in (...) (21 years ago, 28-Sep-05, to lugnet.technic, lugnet.robotics)
|