To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41174 (-10)
  RE: AFOLs and Mindstorms
 
David, I think by pressure sensors they mean touch sensors. Scott -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of David Schilling Sent: Tuesday, November 30, 2004 1:41 PM To: (...) (22 years ago, 30-Nov-04, to lugnet.robotics)
 
  Re: AFOLs and Mindstorms
 
(...) How about 2 "Touch" sensors? I thought the same thing, the first time I read it (when Jan replied to my e-mail, earlier today :) Steve (22 years ago, 30-Nov-04, to lugnet.lego, lugnet.robotics)
 
  Re: AFOLs and Mindstorms
 
I got answers to a some of the questions we've been asking from Jan Beyer about the contest. Question: There seems to be two aspects to the competition. You mention registration is required by February "so you can work at home", as well as an event (...) (22 years ago, 30-Nov-04, to lugnet.lego, lugnet.robotics)
 
  RE: Motor Speed Control
 
(...) :) (...) I'm not sure how the Swan firmware does it, but I have mine set so it cycles every 8 ms. It's on for 0 to 8 ms, then off (brake) for the rest, depending on the speed. That's fast enough to produce a very smooth result. There is no (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  RE: Motor Speed Control
 
(...) Actually, it's more like standing on the brakes, letting go and then gunning the gas, stepping off the gas and standing on the brakes :-) And yes, that WILL use more gas, and more batteries. Now, if the resolutiion of timing for the brake (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  RE: Motor Speed Control
 
(...) Yes, but I think the "power" portion of the cycle will draw more, because it's always trying to go from stop to full speed. Like driving a car with the brakes on. Start with the brake totally pressed, and the more you push on the gas, the less (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  RE: Motor Speed Control
 
(...) The brake function (as far as I know) should not use more battery power as the short circuit is in the driver chip itself. The drivers are MOSFETs, so setting the H bridge to brake does not actually apply any battery power to the motor (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  Re: Motor Speed Control
 
(...) If you are not concerned with remaining pure, this interface (URL) should provide better feedback than the rotation sensor. -Rob A> (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  Re: Motor Speed Control
 
(...) I've been using a power/brake method (instead of power/float) for quite some time in BrickOS. That was one of the first big steps in getting my Legway to work. ( (URL) ) It allows you to program a robot to make smooth turns (slow, instead of (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
 
  Re: Motor Speed Control
 
(...) I'm doing somthing similair at the moment. My robot runs along a track and needs to be controlled so it doesn't go too fast. I've successfully written some code which limits the top speed, you may be able to modify it or just incorparate ideas (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR