 | | RE: Motor Speed Control
|
|
(...) Yes, but I think the "power" portion of the cycle will draw more, because it's always trying to go from stop to full speed. Like driving a car with the brakes on. Start with the brake totally pressed, and the more you push on the gas, the less (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | RE: Motor Speed Control
|
|
(...) The brake function (as far as I know) should not use more battery power as the short circuit is in the driver chip itself. The drivers are MOSFETs, so setting the H bridge to brake does not actually apply any battery power to the motor (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Motor Speed Control
|
|
(...) If you are not concerned with remaining pure, this interface (URL) should provide better feedback than the rotation sensor. -Rob A> (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Motor Speed Control
|
|
(...) I've been using a power/brake method (instead of power/float) for quite some time in BrickOS. That was one of the first big steps in getting my Legway to work. ( (URL) ) It allows you to program a robot to make smooth turns (slow, instead of (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Motor Speed Control
|
|
(...) I'm doing somthing similair at the moment. My robot runs along a track and needs to be controlled so it doesn't go too fast. I've successfully written some code which limits the top speed, you may be able to modify it or just incorparate ideas (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: RCX and the 9v system - help needed!
|
|
If I am understanding the problem correctly here, you should look into using DCC from the RCX. If I do understand your problem, here is a link to a site where a guy tackles using RCX with LEGO trains, and controls them uniquely well with the help of (...) (22 years ago, 30-Nov-04, to lugnet.robotics)
|
| |
 | | Re: RCX and the 9v system - help needed!
|
|
(...) Hi William I found out when I ran the train using the Discovery Scout that it just hurtled around the track, then backwards and forwards if I used the pre-programmed commands. I have not experimented too much with the RCX, but thanks for the (...) (22 years ago, 30-Nov-04, to lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: Motor Speed Control
|
|
Hello Iain, (...) You should definitely try Dick Swan's 10x firmware ((URL) Among other goodies (interpretation speed for example ;o), it features more power levels (128 instead of 8), and a flag to modify behavior of PWM motor control. Standard (...) (22 years ago, 30-Nov-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: RCX and the 9v system - help needed!
|
|
Another option is to have the RCX control a Mindstorms polarity switch which can break the connection between the controller and the track. However this doesn't give the RCX the ability to control the speed of the train. (22 years ago, 30-Nov-04, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Mindstorms in Macworld Magazine
|
|
It's online officially now: (URL) (22 years ago, 30-Nov-04, to lugnet.robotics)
|