 | | IC Problems
|
|
OK all of you IC gurus. How come I can't do this: int m() { int *address; address=&a0; address++; } a0 is a variable defined in an .icb file. I also can't do something like address=address+2; or address[4]=7; Why not? This is all pretty standard C (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC Problems
|
|
OK, OK. RTFM, I know. I looked at the on-line manual, and now realize that IC arrays are different than normal C arrays, and so you can't do stuff like int m() { int *address; address=&a0; address++; } But then the question still remains, how can I (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | IC Problems
|
|
(...) Brian> But then the question still remains, how can I define a list of Brian> consecutive memory locations in a .icb file and then access Brian> them from within a loop in a .c file? [ ... ] Brian> Anybody run into this before or have any (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Quad encoders
|
|
Thx to the advice of many of you I am using encoders from mice as shaft encoders. The code in the libraries does not seem to take into account encoders with TTL signal in quadrature. Therefore I do not get direction from the current software. Maybe (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | battery voltages
|
|
I'm currently trying to get 6V out of my 9.6V battery pack. (I actually looked around for a 6V one, but couldn't find one that would work...) I've opened up the pack, and can access the cell where I can get 6V. However, I'm not sure how to get a (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | charger board problems
|
|
I've managed to stick a wire onto a point in my battery pack which yields 6V. (temporary solution, at least...) However, the charger board doesn't seem to like this new arrangement much. With the lower battery voltage, too much current is flowing (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: charger board problems
|
|
(...) Or just use different motors. ;-) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: charger board problems
|
|
You could just get an adapter that is rated for a lower voltage. Try a nine volt adapter or a universal one that you can experiment with. -Fred -- This message was composed using Articulate Systems' PowerSecretary. Please forgive any sloppiness in (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Can't initialize CONFIG register
|
|
Hello, Everyone: Help! I'm trying to configure the HB. Here's what I get: C:\IC> dlm config0c.s19 -port COM2 -eeprom DLM: 6811 File Downloader... etc. Using COM2 Downloading to EEPROM Downloading config0c.s19, press ESC to abort Downloading eeprom (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | NEW! - Handyboard Hard-to-Get Parts Kit!
|
|
CW Technology is now offering a kit of only the "hard to get" parts for the Handyboard 1.2. Basically, the kit includes everything you can't get at DigiKey and Mouser. The price is very competitive if you consider the minimum orders, shipping, etc. (...) (29 years ago, 11-Feb-96, to lugnet.robotics.handyboard)
|
