To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3821 (+10)
  What is the best way to eliminate mechanical error trough software
 
Hi I built a small circular robot base with differential steering using 3" diameter rubber wheels and optical encoders on both wheels. The motors powering the robot are high efficiency German built gear motors using 300 mA when stalled, and rotating (...) (29 years ago, 11-May-98, to lugnet.robotics.handyboard)
 
  Re: What is the best way to eliminate mechanical error trough software
 
(...) therefore the robot tends to drift toward the side of the slower motor. (...) one, so I'm looking for some input to help me write an efficient program to keep the robot moving straight. I handled this type of problem by creating a new process (...) (29 years ago, 12-May-98, to lugnet.robotics.handyboard)
 
  L293E sense output ??
 
Hi, I'm using a L293E to drive my motors. Each driver has a "sense" output and I don't understand the use of it. How can I use those outputs with the Handy-Board ? Thanks for any help, ......... Fred, Cannes, France EMail: fred.maillet@wanadoo.fr (...) (29 years ago, 13-May-98, to lugnet.robotics.handyboard)
 
  Interrupt counter rate
 
Hi everyone. I use a 4 bits binary counter to measure the no. of pulses emitted from a shaft encoder(TTL output) in order to calulate the speed of a DC motor. But i want to know what is the best frequency that the processor should take the bit (...) (29 years ago, 13-May-98, to lugnet.robotics.handyboard)
 
  Re: HandyBoard 10-16 Servo support
 
(...) I had exactly the same problem. There is a CMOS chip by Motorola called the MC14028B that is a BCD-to-decimal or Binary-to-octal decoder. All that really matters though is that it will take a 4-bit input and decode up to *10* outputs that are (...) (29 years ago, 13-May-98, to lugnet.robotics.handyboard)
 
  Does the HB NEED 9.6 volts?
 
I am planning on using stepper motors with a handy board, which hopefully I will have in a week :) The specs on the HB say it uses 9.6 volts. Is this a required voltage? or can it be another rating as long as it is within the regulators limits. (...) (29 years ago, 13-May-98, to lugnet.robotics.handyboard)
 
  Shorted Handyboard
 
Finishing mounting our handyboard to the chasis of our robot, we shorted the board. A screwdriver made contact near the IR reciever on the bottom right corner of the board. Additionally, the 2.5A fuse blew. After this occured, we have not been able (...) (29 years ago, 13-May-98, to lugnet.robotics.handyboard)
 
  handyboard for sale
 
I have a completed and operational handyboard which I am offering for sale. Contact me at jnbs@wizard.com Thanks Jim (29 years ago, 14-May-98, to lugnet.robotics.handyboard)
 
  Powering and charging handy board
 
Hello. Several questions. What is the best way to charge the board? Through charger board or to teh board directly. Also, when i am chanrging it, am I charging the internal battery or the external NiCD batteries? Also, does the board have its own (...) (29 years ago, 14-May-98, to lugnet.robotics.handyboard)
 
  E Series MCUs
 
I am using an 811E2 part in my handyboard with IC. It is supposed to have problems with this chip. I have not disabled the EEPROM but it still seems to work. I have been having a problem finding the A1FN part. I do not want to buy anymore of the (...) (29 years ago, 15-May-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR