To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37729 (-10)
  Where and what to buy?
 
I'm traveling to United States next week and I'll be staying in Los Angeles for two weeks. I would like to know which LEGO kits or pieces do you recomend that I buy and where to buy them. I know there are cheaper places than the normal ones but as (...) (23 years ago, 27-Jun-03, to lugnet.robotics)
 
  display driver data segment
 
hi folks ! can anyone explain me how the lcddata segment is used in legos ! it seems to me there are some routines which use the rom and some which dont. especially i dont get that the conio.c accesses with the dlcd_* functions the lower lcd data (...) (23 years ago, 26-Jun-03, to lugnet.robotics.rcx.legos)
 
  Re: gear pulley/release system
 
(...) I did a device like this, where the motor ran a differential, which was then used to wind up and release the axle that did the work. One differential output shaft did the winding, and the wound-up axle was held for firing by a gear and ratchet (...) (23 years ago, 27-Jun-03, to lugnet.robotics)
 
  Re: A better full adder!
 
(...) Yes. B and NOT B into the mux formed by two switches that are arranged to never release. (...) But with LEGO pneumatics you can typically get it for free. (...) Yes. When I wrote my post up yesterday I'd forgotten that I needed NOT B as an (...) (23 years ago, 27-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: gear pulley/release system
 
Quoting scott davis <rcx2man@hotmail.com>: (...) Some of my students did this very thing. They used one motor to wind up a spring which was then released to kick a ball. Worked well. Bruce (23 years ago, 27-Jun-03, to lugnet.robotics)
 
  Re: gear pulley/release system
 
I just thought of an idea, haven't had time to try it out but here it is. What if you were to have a sliding worm gear that would wind the arm up when the motor was powered forward and release it when the motor was powered reverse. Like I said, just (...) (23 years ago, 27-Jun-03, to lugnet.robotics)
 
  Send/Receive messages under linux
 
Hi, I've writen a program to send messages to an RCX, depending on programable key strokes. My idea was to drive the robot "blindly", relying on standard firmware messages and replies. I've used Mr. Kekoa Proudfoot's code for packet assembly (files (...) (23 years ago, 19-Jun-03, to lugnet.robotics.rcx)
 
  Re: A better full adder!
 
(...) Ah... it took me a while to figure out what you were doing, but I see now... (reviewing your pics) If your inputs to the XOR were A and B, you use A to drive the piston, and require the presence of both B and NOT B to make the piston move. I (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: A better full adder!
 
(...) AND takes 1 piston + 1 switch using your design. XOR takes 1 piston + 2 switches using my design. OR takes 1 piston + 2 switches using my design. But AND and XOR can be done using the same piston, so 1 piston + 3 switches gets you a half (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
 
  Re: A better full adder!
 
(...) Finally I can compete again! ;^) I can do a half adder with 1 piston and seven switches, plus you get dual polarity pressure. Three switches for AND and four for XOR. This says that I can do single pressure logic line with one piston and three (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR