To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37664 (-10)
  Re: maze solving algorithm
 
Timothy wrote in his posting (2003.06.01): (...) I dont know if i understand you right, but you should not put the ID into the cells but use all 16 bits of an array cell to store 4 maze cells in the way you propose. You can use SHIFT RIGHT operation (...) (23 years ago, 20-Jun-03, to lugnet.robotics)
 
  Re: maze solving algorithm
 
(...) So you used the flood-fill or bellman algorithm described here: (URL) showed that URL in his posting at 2003 may 12). A synchro drive robot allways points in the same direction, so he could be controlled via PC by IR tower. I see problems (...) (23 years ago, 20-Jun-03, to lugnet.robotics)
 
  Re: gear pulley/release system
 
(...) Thank you very much! (...) I don't see any reason why not to try it ;-) Off the top of my head, I can tell you that an RCX loaded with batteries is fairly heavy - maybe you'll need more springs and to pay carfeul attention to balance. Also, I (...) (23 years ago, 20-Jun-03, to lugnet.robotics, lugnet.technic)
 
  Using sensor ports to send data
 
Hello, I did build an I2C device for the RCX a while ago, which is connected to the motor ports of the RCX. It now makes a speed of about 1.2kHz when using BrickOS (still thanks to Mark Riley for helping me whit this). But i think the sensor-ports (...) (23 years ago, 20-Jun-03, to lugnet.robotics)
 
  Re: gear pulley/release system
 
Awesome... Just curious, what do you think about a Two Motor Jump-O-Bot using an RCX and 4 Large Springs? Think that would work? Rich (...) (URL) (...) (URL) you Yahoo!? The New Yahoo! Search - Faster. Easier. Bingo. (URL) (23 years ago, 20-Jun-03, to lugnet.robotics)
 
  Re: gear pulley/release system
 
(...) How about using a caster wheel? I used it for a jumping mechanism, but I think it can also be adapted for a cannon like you describe. Using 1 motor, it keeps firing over and over (URL) (23 years ago, 20-Jun-03, to lugnet.robotics, FTX)
 
  Re: Switching Direction
 
(...) I tried it and it works for me :-) On an unrelated note am I right in thingking the only way to get the file "afxdtctl.h" would be to upgrade to Visual c++ Ver 6? Steve (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  Re: 8455 - new form factor for large piston and switches
 
(...) Rob, Nope. Only large pistons. There is no performance difference between the pre-2003 pistons and the 2003 pistons. Form factor is the only difference. (...) The resistance to flipping is the same between virgin old style and virgin new style (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  RE: 8455 - new form factor for large piston and switches
 
Kevin, Did 8455 come with small pneumatic cylinders, or just large ones? Does the new switch have better, worse, or comparable action to the old switch, in your opinion? Thanks, Rob (...) (URL) new form factor switch is side by side with its (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  Re: All Lego Ack Circuit for LDCC
 
(...) indeed, the construction of this beast may be very different (e.g. metallic contact, 0 resistance... and a lot of bounce almost completely avoided with conductive rubber) Philo (23 years ago, 19-Jun-03, to lugnet.trains, lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR