To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37454 (-10)
  Re: DCC for the RCX
 
In lugnet.robotics.rcx, Esger Abbink wrote: <snip> (...) Perfectly understood. Thanks! My problem has always been that I wanted to get into electronics, but all those resistors 'n such used to have all these coloured stipes to denote the different (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
i have a question concerning how the DCC signal is sent Is it just sort of a "rider" on top of the power similar to X-10 home automation signals? If so could not the RCX be protected with diodes and used in conjunction with a standard train (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
(...) put in (...) Thanks, Larry, and thanks to all who posted or emailed. (...) one (...) Or is (...) It's important that the motor outputs share the load as evenly as possible. A stalled train motor can draw as much as 750ma, while a single motor (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
 
(...) What about ultrasonic beacons at each corner of the room? Then use the old-fashioned Hyperfix calculations. It should cost only a few dollars in hardware - and six months of software development :-). Are they available off the shelf or are (...) (23 years ago, 30-May-03, to lugnet.robotics)
 
  Communicating between two RCX'es with cable
 
Hi there, Long time, no see - I've finally managed to dig out my Lego once again... First of all; I'm very pleased to see the outcome of LejOS 2.x - with Proximity, LLC, integration of rcxcomm, etc. Now, I was wondering if it would be possible (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx.java)
 
  Re: DCC for the RCX
 
(...) I forget if I already replied with how nifty this is. I spotlighted it, I put in a news article at ILTCO (we're having some domain problems right now, a temporary url is iltco.northcomp.com) and I added it to the .trains header That ought to (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
 
(...) are (...) probably (...) inch...after (...) probably (...) I still think that Dead Reckoning could be solved by using three Spybotics towers at the different emissions placed around and have the rcx using polling (get message?) to determine (...) (23 years ago, 29-May-03, to lugnet.robotics)
 
  Re: DCC for the RCX
 
(...) Hi Dave, no you wouldnt need any resistors or diodes. Esger (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
(...) Sorry, my earlier post should have been more clear. I was just commenting on the fact that in general a resistor is _not_ a good way to reduce voltage to a train motor. And you recalled correctly: diode's are "one-way". Thats why you need to (...) (23 years ago, 29-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
(...) The problem with inductive load is that when current is interrupted, they generate large voltage spikes with reverse polarity. The diode absorbs these spikes and avoids destroying the driver... Philo (23 years ago, 29-May-03, to lugnet.robotics.rcx, lugnet.trains)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR