To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37439 (-10)
  Re: DCC for the RCX
 
(...) output? Dave, I used a 1N4002. It's a fairly common 1 amp switching diode. Here's a picture from my latest decoder install: (URL) that the banded end of the diode gets the blue lead from the decoder. The unbanded end gets the white lead. If (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
 
(...) Yes - but that is precisely 100% of the problem. There is no known convenient/cheap GPS-like system with the properties we desire. Camera's above the arena and things pasted onto the floor are not possible in many real-world situations. The (...) (23 years ago, 28-May-03, to lugnet.robotics)
 
  Re: DCC for the RCX
 
In lugnet.robotics.rcx, Mark Riley wrote: <snip> (...) Mucho appreciated Mark. The Diode--any diode will do? and just solder it across the connector output? Take care, Dave (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
(...) I (...) resistors (...) goes (...) run (...) the (...) isn't (...) reduce the (...) David, When I installed my first decoders (Digitrax DN121), I omitted the capacitors, figuring if the buzzing was annoying, I could always add them later. As (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
 
(...) items (...) the (...) (that (...) Even commercial guidence systems use periodic recalibration, for example with small magnets in the floor. The robot knows where the magnets are and if it finds a magnet off center to it's expected position it (...) (23 years ago, 28-May-03, to lugnet.robotics)
 
  Re: DCC for the RCX
 
<snip> (...) Hey Esger I'm not an electronic specialist by any stretch of the imagination (though not by lack of trying) But commercially available DCC controllers and stuff mostly run at 12 volts (from the research I read), but the RCX runs at 9 (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: DCC for the RCX
 
(...) As I run 12v stuff I dont know the 9v motor good enough to comment on the capacitors but I dont think it's that good an idea to use a resistor to drop the voltage. Use one or more (zener)diode's instead. Esger (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: Remote control under linux
 
(...) I'm not sure I understand the question. Are you saying that you want Program #1 to start when you press button P1 and stop running when you release the button? This isn't how the remote works, but you could just have your program send the Stop (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, FTX)
 
  need help for MLCAD:"add new piece to library"
 
Hi everybody, there are missing parts in my MLCAD library.For example I do not have small pneumatic cylinder or pneumatic switch. how can I get on? do I have to create my own custom part or is there any optional free library.If I create my own piece (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx)
 
  Re: DCC for the RCX
 
(...) Oh My Goodness! This is what I've been waiting for--when I priced out DCC controllers, they were 200+ CDN... If I can get one of my many RCX's to do it, well that's entirely another matter. When I originally did the research and found the cost (...) (23 years ago, 28-May-03, to lugnet.robotics.rcx, lugnet.trains)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR