To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3706 (+10)
  IR Transmit
 
I am trying to get two handyboards to exchange data via the IR. I have tried code from the Dave Negro and Pete McCann code, but I still cannot get reliable data transmission at any range. Summary of situation: REC80-IR.icb: Reliable reception of (...) (29 years ago, 28-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
(...) There is a little strip of four pins for external battery power and are available with the standard battery pack installed. Two of these are battery positive, two are at ground. Shorting them out is a good way to let the smoke genie loose. (29 years ago, 28-Apr-98, to lugnet.robotics.handyboard)
 
  More Polaroid problems!
 
Well, everything seemed ok, but now (we are in a crunch again, the final presentation is Friday!) there is another problem. We seem to be getting some erroneous distances and I think I know why. The echo signal is pretty noisy, so my question is, (...) (29 years ago, 29-Apr-98, to lugnet.robotics.handyboard)
 
  Smooth PWM with IC 3.2
 
I know this is an old thread but I am just now getting to the point where I can finally start programming. I am using IC 3.2 and the expansion board. I downloaded the smooth PWM routines from Newton Labs but I get errors when I load them into the (...) (29 years ago, 29-Apr-98, to lugnet.robotics.handyboard)
 
  memory expansion
 
Hello, Has anyone figured out a GOOD way to expand the memory on the Handy Board? I would like to try using a 32 pin simm (I have sizes ranging from 256k to 4M) to store mappings (distance and turns) created by the initial "adventure" it takes of (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  memory expansion
 
Hello, Has anyone figured out a GOOD way to expand the memory on the Handy Board? I would like to try using a 32 pin simm (I have sizes ranging from 256k to 4M) to store mappings (distance and turns) created by the initial "adventure" it takes of (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Quick prototyping technologies
 
I am looking for good methods for quick prototyping and would appreciate all suggestions. In Mobile Robots by Joseph L. Jones and Anita M Flynn, they suggest using Scotchflex by 3M and Speedwire by Bicc-Vero company as two good alternatives to using (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  V2x AND Polaroid Sonar
 
Hello again, Has anyone been able to wire the V2x compass and the Polaroid sonar device both to the HandyBoard and, if so, how was it done? Thanks, Scott sherman@plains.nodak.edu CSG ITS NDSU (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Schematic Question
 
I have been looking at the schematic for the handyboard and the RS232/Charger board. I noticed something that seems wrong. But how could it since this has been out for some time? Power goes out pin 4 of J10 on the Charger board and pin 4 on (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Schematic Question
 
You're missing the fact that the telephone style RJ-11 cable is an inverting cable. see page 11 of 16 of the Handyboard FAQ at (URL) a discussion and diagram of this (and the consequences of using the wrong cable!). -patrick ---...--- (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR