To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3681 (+20)
  Re: IC stack problem
 
(...) The funny thing is, it doesn't complain about arrays smaller than 4x4. All values are stored correctly for an array of size 3x3. What's this 'magic' number 4 then? Jan Sipke van der veen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Serial Communication: HB -> Win95
 
To answer my own question, at least partially, here is a Win95 Host program to communicate (single bytes) with the HandyBoard over a serial line: /* Win95 Visual C++ Host Code to talk to HandyBoard */ #include <conio.h> // _outp, _inp #include (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
When it first worked for me, I used the HB NiCd. I grounded binh and it worked. I used binh to measure like 7 inches and it worked fine too. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
The 100, 50, 40, etc. are not really "speeds". They are power. It is related to the average voltage level of your output. Speed depends on the torque and characteristics of your motor. You can hold on the the wheel and still drive the motor at 100. (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
Well, actually, it's not power either. Power is V * I. Sorry, it's actually the voltage. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
oh yeah? Well, what about the capcitor, huh? ;) ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  A few questions....
 
First I want everyone to know two things. First I am new to this list. Second, I have moderate knowledge of electronics.... Until about a few weeks ago, I had been working with Basic Stamps 1 and 2. After looking at all the information about (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Trinity College contest report
 
Hi all, first, the URL: (URL) went to last weekend's Fire-Fighting Robot Contest at Trinity College, along with my colleague Steve Ocko, who had built a cute robot based on our network-cricket technology (see (URL) for more on that). We spent about (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
(...) residual noise? It was my understanding that the Polaroid module used pulse time differentials to relay distance information. One need only look at the difference in time, between the leading edge of the init pulse, and the leading edge of the (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
(...) Are you using the "smooth" PWM motor routines? Note also, that a DC motor does not change velocity linearly with an increase in current unless it is under load. This was a recently asked question on the list. Maybe grepping the digest for (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Generally the capacitor is the problem :-) The capacitor in the original note is there to pull BINH true* to allow the sensor to detect things that are closer than 18". Generally, when you include it, unless the design of the system holding the (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  examples
 
I was wondering if anyone out there could send me some very basic, easy to understand programs that could help me figure out how to use sonar modules. Thanks, Richard (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Hey, I just wanted to thank everybody for there help with this, it did turn out to be the pull up resistor problem, I feel like a moron. We used the handyboardy sonar interfacing schematic when we wired it up and failed to realize that we aren't (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  A Few Questions
 
First I want everyone to know two things. First I am new to this list. Second, I have moderate knowledge of electronics.... Until about a few weeks ago, I had been working with Basic Stamps 1 and 2. After looking at all the information about (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Stepper motor help
 
I am planning on using stepper motors w/ a handy board and will be powering them separately from the rest of the board. What type of motor should I use? I have seen 6 and 12 volt motors availble, if anyone can recommend which to use I would (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  subscribe
 
(29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IC stack problem
 
Dear Jan-Sipke, Two-dimensional arrays are not implemented in the freeware IC 2.8 -- sorry. I just tested and your code works fine with IC 3.1/3.2. -- Randy ---...--- (...) (29 years ago, 24-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
Hi For a relatively simple solution you may want to look at (URL) have connected and run steppers using this method. It does not get the best from the motors but it will let you experiment easily. (29 years ago, 24-Apr-98, to lugnet.robotics.handyboard)
 
  Smooth PWM routines for IC 3.1/3.2
 
Thanks to Julian Skidmore and Scott Seaton, we have a version of pcode and libraries for IC 3.1/3.2 which implement Julian's "smooth pwm" routines for the MIT Handyboard. To grab these, please go to the following address: (...) (29 years ago, 25-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
(...) Thanks for this excellent article on driving stepper motors from the Handboard. One little yet very important question: when you say "the common wires need to be connected to the motor positive supply" what exact handyboard pinout are you (...) (29 years ago, 25-Apr-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR