 | | Re: Received my RIS 2.0 - the two motors run at different speed! :-(((
|
|
First of all, let me say that I very much appreciate your deep insight and your math formulas, which I have forgotten years ago. :) After further testing and measuring, I found that the difference is much larger - it actually deviates a good one (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
(...) high (...) frames (...) very (...) anyone (...) I (...) BrickOS (...) In the current release of BrickOS, the motors only get updated by the timer ISR every 2ms, so that probably explains why trying to twiddle the bits any faster than that (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
Steve is absolutely right and what he said is exactly what I'd recommend. When writing for loops, you can do the same test as Steve suggested: running the loop x 1000 times and then beep. Divide the stopwatch time by 1000 and you have the timing of (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
Steve, Very good suggestions! (...) Bastiaan v.Kesteren, I second Steve's recommendation, using loops for timing between command segments. You will not get very far using BrickOS msleep because of the 1ms minimum timing. Also, you may find the (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Received my RIS 2.0 - the two motors run at different speed! :-(((
|
|
(...) Is it? Did you do the math or are your just guessing? There isn't enough information to figure the math from what you've told us... It depends on how wide your robot is and what units that triangle is in (feet? meters? miles?). But let's make (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
(...) Erm...no...you have some trouble with your numbers! 1000us == 1ms so: 4.7us == 0.0047ms !! (...) Yikes! Nooo...ooo! 250ns == 0.25us == 0.00025ms Remember: ms is a millisecond which is 1/1000th second. us is a microsecond which is 1/1000000th (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Received my RIS 2.0 - the two motors run at different speed! :-(((
|
|
(...) It's definitely higher than 10%. When my rover is running far enough, it's turning right enough to form a triangle whose side ratio is about 1 length for every 6 traveled, so it's somewhere between 15% and 20% difference. I will call Lego (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Received my RIS 2.0 - the two motors run at different speed! :-(((
|
|
(...) Yes - they've recently changed the design slightly - you should check the mailing list archives - there has been a lot of discussion about this. (...) Motors don't all run at the same speed - that's a given - and you have to design your robot (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | I2C device for the RCX
|
|
Hello, A while ago, there whas a short thread about the I2C device for the RCX from Elector Electronics magazine No. 309, APRIL 2002. The conclusion was: way to slow, 3 commands per second was the maximum possible. Ive build it anyway, just for fun (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|
| |
 | | Received my RIS 2.0 - the two motors run at different speed! :-(((
|
|
Hello all, I opened the box of my first Mindstorms set yesterday, and it came with two motors that are slightly different from the usual motors I have, they are much lighter, have notches, and sound differently than normal geared down motors (such (...) (24 years ago, 11-Jan-03, to lugnet.robotics)
|