 | | Shufflebot Concept
|
|
Is there any way to make a shuffling (stompbot) drive where three shufflers are used on each side. When one goes up, the other two go down, and when those two go up the other one goes down. This is used to provide locomotion. The best example of (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | RE: Firmware download troubles
|
|
The size of the firmware isn't going past the 0xcc00 boundary, is it? The firmware in the RCX only does a sum on the bytes up to 0xCBFF in the downloaded firmware, as far as I recall... Cheers, Ralph (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: BrickOS Threading...
|
|
Joe, (...) Maybe a special kernel build for testing purposes that increments the lower sys_time word by 0x4000 instead of 1. This will greatly increase the opportunity for this glitch to occur (from once every 65 seconds to once every 4ms.) You (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Hammer Help
|
|
Thanks for the response. I've decided to stay away from string on the robot as string can get easily entangled, especially if battling another robot. I took a break from trying a design using gears and differentials - I was getting really (...) (24 years ago, 13-Dec-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Hammer Help
|
|
In the prototype I used string and winch to set the hammer. I've decided not to use it on the robot - string can too easily get caught and entangled in stuff, especially if it goes up agianst another robot. On the prototype it works surprisingly (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | Re: Firmware download troubles
|
|
(...) The problem he's describing, if it's the same one I have, is independant of the position, direction, and power level of the tower. It seems to have something to do with BrixCC itself. The only thing I find puzzling is that Matt (the other Matt (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: BrickOS Threading...
|
|
Steve, I checked in some changes this morning (into cvs) to put the motor controller back at the 1 ms interval. However, I want to complete the get_sys_time() updates that Mark Riley has proposed; so that can be tested as well. I am not sure when (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Firmware download troubles
|
|
(...) It's funny that you should bring this up - I've had exactly the same problems with several RCX's and downloading firmware from BrixCC. The only solution I've been able to find is to download the firmware using the RIS2.0 software and then (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: sys_time (long post)
|
|
(...) It turns out that the nature of the glitch depends on the order you read the upper and lower 16-bits of sys_time. If the compiler generates code that reads the high word first (which it seems to do), then your example will work. However, if (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Fw: [handyboard] xmas songs
|
|
----- Original Message ----- From: <x01101001@yahoo.com> To: <handyboard@yahoogroups.com> Sent: Friday, December 13, 2002 8:19 PM Subject: [handyboard] xmas songs (...) (24 years ago, 13-Dec-02, to lugnet.robotics.handyboard)
|