To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *35759 (-10)
  Re: Firmware download troubles
 
(...) Look at Edit/Preferences. On the General tab is a checkbox labeled "Use fast mode when downloading firmware" You can uncheck that option to use normal speed firmware downloads via BricxCC. John Hansen (URL) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
The low buzz tone is an error generated by the ROM firmware for failure condition detected as part of the "unlock firmware" opcode. There are two causes of this. [1] ROM software calculates a checksum value of the downloaded firmware and this (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
(...) ... (...) Dick and others, Thanks - this helped. What I did to solve this was run the NCQ command-line download at "normal" speed. This worked the first time. Interestingly, I am not sure that the Bricx (v3.3) download was running quad speed (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
A likely explanation for your downloading problem is the following. Standard Lego software uses 2400 baud data rate and a protocol that sends "double" bytes. The "double" byte is that each data byte is followed by its complement. Alternative (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: want to get inentors kit but...
 
(...) If you want to use the 'official' Lego software, then I'm not sure what Windoze OS's are supported - but certainly Linux isn't. However, many (most even?) serious users end up using a 3rd party software package called 'Not Quite C' (NQC) which (...) (24 years ago, 10-Dec-02, to lugnet.robotics)
 
  RE: Installation Help!
 
Max, Aha! I did that and it got a lot further this time, but still failed. I'll have to wade through the log file to try and pinpoint where it went wrong as I don't want to post the whole 180k. Thanks for your help! Andy -----Original Message----- (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx.legos)
 
  Re: Firmware download troubles
 
Matt, I discovered that the IR LED's and detector on my serial tower was located higher than I expected and pointed upward somewhat. I was able to get better transfers when the tower was leaning forward (pointing downward so to speak). Otherwise, I (...) (24 years ago, 9-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
Also: When it seems to get to the very end before the error appears, I sometimes get a long (3-4 seconds) low tone from the RCX. Matt (24 years ago, 9-Dec-02, to lugnet.robotics.rcx)
 
  Firmware download troubles
 
Hi All, I have pulled my RCX out of summer storage and I am trying to bring it to life. I have tried to download the 2.0 Firmware (firm0328.lgo) dozens of times with no success. It starts to download, then somewhere in the middle, or very close to (...) (24 years ago, 9-Dec-02, to lugnet.robotics.rcx)
 
  Re: Installation Help!
 
(...) You need to install the Cygwin gcc package. You need the normal Cygwin gcc to build the Cygwin->H8300 cross-compiler gcc. Max. (24 years ago, 9-Dec-02, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR