To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *35069 (-10)
  Re: Announcing LegWay, Finally
 
(...) Actually, you can look at the rate of change. As the surface is tilted, the robot would start to fall as it tries to maintain a distance. Then, the rate of change will increase, so it will compensate by moving the other direction (return to (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  Re: Announcing LegWay, Finally
 
(...) There's some difficulties with hooking 4 analog sensors up to a single RCX. ;-) Even if there weren't however, that wouldn't change the fact that the range sensors (light or otherwise) cannot tell the difference between the ground being tilted (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  Re: Announcing LegWay, Finally
 
(...) Thanks. Most of my robots are more about function than form, but I also think it's important to have a good bridge crew... (URL) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  RE: Announcing LegWay, Finally
 
Hi people, about inclined surfaces, will the LegWay works with four light sensors? C (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  Re: Announcing LegWay, Finally
 
(...) Thanks (...) hmm. no. A couple people have asked this question. Actually, I've put it on a table, and lifted one side of the table. LegWay will tilt, to correct for the angle. (while it rolls down the hill!) It constantly checks the distance (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  RE: Announcing LegWay, Finally
 
As everyone can see, I think my brain stopped working this past few minutes :> Ok. Now that I got my brain working again (I hope) let's give another go at this. LegWay and an inclined surface: The LegWay will try to climb up to the point where the (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  Re: Announcing LegWay, Finally
 
(...) I think it's absolutely fabulous! A clever solution to the tricky task of top-heavy balancing...for that really is the essence of it. I like the simple approach involving very few parts. Well done! BTW, in looking at your website I noticed (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  RE: Announcing LegWay, Finally
 
OOPS.... SORRY for the "duplicate" msg! :/ I forgot I was using the lego-robotics@crynwr.com instead of the "need confirmation before posting" lugnet.robotics news list. Sorry. mc. (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  RE: Announcing LegWay, Finally
 
(...) Congrats for making *THE* LegWay :) ...a much talked theoretically possible project, but you done it :) Question: Your solution only works on perfectly horizontal surfaces, right ? What happens if you put a inclined surface in front of the (...) (24 years ago, 17-Oct-02, to lugnet.robotics)
 
  RE: Announcing LegWay, Finally
 
(...) Congrats for making *THE* LegWay :) ...a much talked theoretically possible project, but you done it :) Question: Your solution only works on perfectly horizontal surfaces, right ? What happens if you put a inclined surface in front of the (...) (24 years ago, 17-Oct-02, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR