To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *34639 (-10)
  Re: Ipaq 3835: using building programs and using built-in IR
 
"Rob Limbaugh" <rlimbaugh@ureach.com> wrote in message news:H29JA5.D7t@lugnet.com... (...) I was not referring to just simple commands. You can use some learning remotes for that. I'm talking about NQC support. Dean (...) simulate (...) simple (...) (24 years ago, 12-Sep-02, to lugnet.robotics.palm, lugnet.robotics, lugnet.robotics.spybotics)
 
  RE: Questions about the first version of the control center console
 
Agreed. I had one of the older kind of control center (the one with only two colors of buttons) and it had no wires sticking out of it. I believe the control center you are looking at has been modified. (...) (24 years ago, 12-Sep-02, to lugnet.robotics)
 
  Follow-up... RE: How to install VC in Windows 2000
 
I've been alerted that the steps didn't work for one person... the problem they had was the cam drivers wouldn't load. I recalled that when I originally tried to force an installation, I installed the Logitech USB Camera drivers from the VC CD. The (...) (24 years ago, 12-Sep-02, to lugnet.robotics)
 
  RE: How to install VC in Windows 2000
 
Hello, I'm not sure, but my guess is that there is a similar approach. Someone has posted a current solution for XP, but you need to have a copy of the installed VC directory off of a win98/winMe installation first. Unfortunately, it involves the (...) (24 years ago, 12-Sep-02, to lugnet.robotics)
 
  Re: RCX to RCX
 
(...) Seems OK. (...) > I would like to encorporate 2 RCX bricks into one robot to increase the number of sensor > and motor ports. If you use NQC (and you should) then my page here: (URL) give you all you need. ---...--- Steve Baker ---...--- Mail (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
 
  Re: Over Charging
 
Fred, We had the same problem and traced it to the resistor. We can try the ZAP mode, but for future reference we would like to know the value you used to replace the 47 Ohm 1/2 watt resistor. Any chance we could get that information? Thanks, Dan (...) (24 years ago, 11-Sep-02, to lugnet.robotics.handyboard)
 
  Re: Questions about the first version of the control center console
 
(...) I think these are not original, so you will have to open the case to see where they end. This will tell you what you can safely do with them. Or if not, you can post another pic of the opened case ... Greetings Horst (24 years ago, 11-Sep-02, to lugnet.technic, lugnet.robotics)
 
  Re: RCX to RCX
 
The answer very much depends on what you are using as a programming environment. The simple answer for NQC is Message(). I've used this very simple interface to do exactly what you describe needing. It is covered in NQC's accompanying documentation. (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
 
  RCX to RCX
 
I hope I am using this mailing system correctly. I am a first time user. I have one question to ask right now: Will someone point me in the right direction for instructions on RCX to RCX communication. I would like to encorporate 2 RCX bricks into (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
 
  Tutorial: use RCX motor output to switch devices / build your own interface
 
(...) I hope this tutorial will give you some good ideas of your own too! It can be found here: (URL) please e-mail me with your comments or mistakes in the tutorial, or post it here. Have fun, Remko (24 years ago, 11-Sep-02, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR