 | | Re: Over Charging
|
|
Fred, We had the same problem and traced it to the resistor. We can try the ZAP mode, but for future reference we would like to know the value you used to replace the 47 Ohm 1/2 watt resistor. Any chance we could get that information? Thanks, Dan (...) (24 years ago, 11-Sep-02, to lugnet.robotics.handyboard)
|
| |
 | | Re: Questions about the first version of the control center console
|
|
(...) I think these are not original, so you will have to open the case to see where they end. This will tell you what you can safely do with them. Or if not, you can post another pic of the opened case ... Greetings Horst (24 years ago, 11-Sep-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: RCX to RCX
|
|
The answer very much depends on what you are using as a programming environment. The simple answer for NQC is Message(). I've used this very simple interface to do exactly what you describe needing. It is covered in NQC's accompanying documentation. (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
|
| |
 | | RCX to RCX
|
|
I hope I am using this mailing system correctly. I am a first time user. I have one question to ask right now: Will someone point me in the right direction for instructions on RCX to RCX communication. I would like to encorporate 2 RCX bricks into (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
|
| |
 | | Tutorial: use RCX motor output to switch devices / build your own interface
|
|
(...) I hope this tutorial will give you some good ideas of your own too! It can be found here: (URL) please e-mail me with your comments or mistakes in the tutorial, or post it here. Have fun, Remko (24 years ago, 11-Sep-02, to lugnet.robotics)
|
| |
 | | Re: Iveco Eurostar with extensible trailer
|
|
Its very very simple how the steering works. If you ever have taken a good look on the fifth wheel on a truck, (europian ones not sure about US trucks) there are a little cutout piece in the rear, and behind the king pin (the pin on the trailer (...) (24 years ago, 11-Sep-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | IR vs. RC
|
|
Heya all, maybe stupid question, maybe it was discused before but where (or what) is the main diference in the two LEGO Racer sets controled by Infra Red and radio Control ? I know what is IR and RC but where are the diferences by controling the (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
|
| |
 | | Re: How to install VC in Windows 2000
|
|
Rob, Thanks for taking the time to create and post these directions. I am considering installing VC on XP. Do you know if the apcompat.exe file (or something similar) is used to achieve compatibility for the XP OS? Thanks. Laura (...) (24 years ago, 11-Sep-02, to lugnet.robotics)
|
| |
 | | Questions about the first version of the control center console
|
|
Hi all, I've just picked up one of those by-the-pound pile of bricks from an ebay auction. It includes the 2840 Technic Control Center console((URL) that came with the first Technic Control Center set - 8094 ((URL) as some of you might know, this (...) (24 years ago, 11-Sep-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Ipaq 3835: using building programs and using built-in IR
|
|
(...) That's not true... I've controlled my RCX, Scout, and Spybotic with my iPAQ 3635 through the IrDA port. I used a demo version of "TV Remote Controller v3.0" from (URL) think those programs use the 3-wire mode of IrDA. More info here: (URL) (...) (24 years ago, 11-Sep-02, to lugnet.robotics.palm, lugnet.robotics, lugnet.robotics.spybotics)
|