 | | Legousbtower configuration 4.
|
|
Dear Juergen, As a response to the question on your webpage, I've tried configuration 4 of the legusbtower (legusbtower + uhci + nqc). I had no issues in using my setup to download the firmware to the brick. The response from the RCX brick sometimes (...) (24 years ago, 16-Jan-02, to lugnet.robotics)
|
| |
| | Re: wireless RF RCX communication?
|
|
There are devices sold by Radio Shack/Future Shop/etc called (i think) "remote extenders". Basically, they have 2 pieces. 1 is an infrared receiver and radio transmitter, and the other is a radio reciever and ir transmitter. I think they are one-way (...) (24 years ago, 16-Jan-02, to lugnet.robotics)
|
| |
| | Re: Cygwin problems
|
|
Ben I recommend you read the Howto from the sourceforge docs section, or even better buy the Extreme Mindstorms book (Extreme Mindstorms; D. Baum, M. Gasperi, R. Hempel, L. Villa; Apress; ISBN: 1893115844 ) . Both give a good explanation of legOS. (...) (24 years ago, 16-Jan-02, to lugnet.robotics.rcx.legos)
|
| |
| | Cygwin problems
|
|
Hi all, i am having problems with cygwin. It doesnt help that i dont know what all these linux commands mean but i will explain my problems now. I have intstalled all the software to my system ok and the linux emulator seems to work fine(i can use (...) (24 years ago, 16-Jan-02, to lugnet.robotics.rcx.legos)
|
| |
| | Cybermaster CD
|
|
(...) Lego were not able to find me an english Cybermaster CD, so my Cybermaster is sitting there unused as I can't figure out how to use the german software. Is anyone on this group willing to lend me a CD-R of an english CD? I would reimburse you (...) (24 years ago, 16-Jan-02, to lugnet.robotics.cybermaster)
|
| |
| | SDK 2.0
|
|
Hi everybody. Does anyone downloaded the new SDK 2.0 for RIS2.0? When i try to download the zip file, everything seems to work, but when i launch the EXE inside i get an error message "Corrupt Cabinet file" The download address is: (URL) in advance. (...) (24 years ago, 16-Jan-02, to lugnet.robotics.rcx)
|
| |
| | Re: Help! Hanyboard Assembly Testing problem!---I think solved!
|
|
There was a very undetcible component-side solder bridge between pins 2 and 3 of RP4. I might not know until tomorrow when I can get a replacement for RP4 (apparently I'm not very good at desoldering, and I didn't see the bridge at all until I (...) (24 years ago, 16-Jan-02, to lugnet.robotics.handyboard)
|
| |
| | Re: threads
|
|
Thanks Albert (...) still (...) How do I check this? There are no other tasks that can kill threads apart from this one. I also checked process IDs after creation and before killing. Best regards, mike (24 years ago, 16-Jan-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: I'm sure this has been done to death
|
|
Best source is other Mindstorms Sets - preferrably heavily discounted. Older RIS sets have gone in chain stores for as low as $69. Expansion sets are available through a range of places online as closeouts at varying discounts. CompUSA and BestBuy (...) (24 years ago, 16-Jan-02, to lugnet.robotics)
|
| |
| | Re: Help! Hanyboard Assembly Testing problem!
|
|
Hi, Thanks for your reply. RP4 has the part # 88102G, and adjacent pairs of pins have resistance of 1k (ie, 4 discrete resistors). Ok, Tell me if this sounds really strange... R15 is installed, but tested at about 1k ohms, not 47k. I remove the (...) (24 years ago, 16-Jan-02, to lugnet.robotics.handyboard)
|
