To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3136 (+10)
  8 bits A/D bus
 
Hello, I've bought a handy board, and try to build a card to enserve two motors. On that card I have a IC chip (HP hctl 1100) that needs to be link to a 8 bits Adress/data bus in both reading and writing modes. My problem is where to pick such a bus (...) (29 years ago, 14-Jan-98, to lugnet.robotics.handyboard)
 
  Re: 8 bits A/D bus
 
I am building a somewhat similar circuit (a high-current h-bridge for the handy board), although I only need to read the data lines. However, the same approach will work for writing to the bus. My circuit lives on a board which plugs in between the (...) (29 years ago, 14-Jan-98, to lugnet.robotics.handyboard)
 
  Re: 8 bits A/D bus
 
Please read Appendix B of the 6.270 Robot Builders Guide. This explains how to interface latches with the Handy Board. See (URL) Hello, (...) s (...) k (...) e (...) (29 years ago, 14-Jan-98, to lugnet.robotics.handyboard)
 
  Initialization Problemas. S.O.S.
 
Hello Out there! We are a group of computer science students here in Universidad Simon Bolivar (Caracas, Venezuela). We are currently teaching a robotics course as we took it last trimester. We are having trouble initializing the handyboards. The IC (...) (29 years ago, 15-Jan-98, to lugnet.robotics.handyboard)
 
  using handyboard with vernier ULI
 
Hello from New Mexico I'm currently teaching a robotics class at the high school level and we have been exploring the possibility of creating a rover that will eventually be independent and have enough AI to make decisions that will get it through (...) (29 years ago, 15-Jan-98, to lugnet.robotics.handyboard)
 
  Hooking up PA7
 
I downloaded the 9600 baud serial driver that uses Digital input #9 or PA7 (I think). It is really unclear to me which connector I should plug into. In between the IR I/O section and the BATTPWR LED's there are a bunch of connectors. The manual (...) (29 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
 
  Config Register error
 
hello all, I have only started building the Handy Board and have run into some problems at the very start when i first conected the part built board. I have build it as far as the power supply, stop switch and 68hc11 installed, memory and lcd. When (...) (29 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
 
  Re: Config Register error
 
I had the same problem. I was never able to get HBDL to set the config register. I used DL to set it on one board and DLM on another. I used the information from the HandyBoard technical reference manual to use these programs. (URL) the config (...) (29 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
 
  Handy board troubles.
 
I have various handyboard and i never use the IR ports. So i'm assembling one handy, and don't put al the components asociated to that ports. I download anyprogram to that's board and never boot again!!!! The transmision is o.k. but don't start (...) (29 years ago, 16-Jan-98, to lugnet.robotics.handyboard)
 
  Re: Shaft encoder
 
(...) Hi there, Would these chips be suitable for interfacing a mouse to the Handyboard? My robot incorporates a mouse as a castor wheel and I want to use its shaft encoders as position/velocity sensors (relative) for the robot, but I don't know (...) (29 years ago, 16-Jan-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR