To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *30644 (-20)
  Re: 3804 RIS 2.0 VS 9747 RIS 1.5
 
Hi John, I sure appreciate your help and thank you very much. I was tempted to buy it at TRU in Canada, they had a Can$20 off on the original Can$300... Not a big deal but it could help a bit and TRU is the only place I can buy them. Best regards, (...) (25 years ago, 27-Nov-01, to lugnet.robotics)
 
  Bi-Colour LED Lego Lights
 
Anyone who's interested in adding coloured lights to thier creations, I have some for auction: (URL) controlled by a Mindstorms RCX, these can be set to one of two colours. If just attached to a 9V battery box, reversing the switch or the connector (...) (25 years ago, 27-Nov-01, to lugnet.robotics)
 
  Re: 3804 RIS 2.0 VS 9747 RIS 1.5
 
(...) differences are: 1) Software upgrade - available separately for about $20 2) use of a USB IR transmitter instead of a battery powered serial port transmitter. varying opinions as to which is better with longer range. 3)There is a length of (...) (25 years ago, 27-Nov-01, to lugnet.robotics)
 
  3804 RIS 2.0 VS 9747 RIS 1.5
 
OOOOPS! I meant this one 9747. Forget about my previous post. So what is the difference between those 2 sets? Thanks again, Jean-marc (25 years ago, 27-Nov-01, to lugnet.robotics)
 
  3804 RIS 2.0 VS 9719 RIS 1.0
 
Hello there, Do you know what is the difference between those 2 sets (beside 10 pieces less) The components looks the same. Has someone made the comparaison yet? Thanks for your reply, Jean-Marc (25 years ago, 27-Nov-01, to lugnet.robotics)
 
  Re: Problems with the USB tower
 
Hi!Hary,I am sorry I replied to your mail from outside the lugnet list.Please reply to the list and I will make sure that I don't mess up. Regards, Rajendra (...) (25 years ago, 27-Nov-01, to lugnet.robotics.rcx.legos)
 
  Re: Problems with the USB tower
 
Where'd you the get the patch for LegOS that can use the USB tower? - Hary (...) (25 years ago, 24-Nov-01, to lugnet.robotics.rcx.legos)
 
  Re: Testers/Evaluators wanted
 
(...) Hi: I would like to be a tester. My email address is joev@frontiernet.net (25 years ago, 26-Nov-01, to lugnet.technic, lugnet.robotics)
 
  Re: Programming RCX using Delphi
 
hi Robert, Besides using spirit.ocx (I threw it away because of it's limitations and strange behaviour), you can also send/receive commands through a normal RS232 driver. I've done this in Delphi-5 (only RS232), you can download my sources here: (...) (25 years ago, 26-Nov-01, to lugnet.robotics)
 
  Re: Programming RCX using Delphi
 
Hi I used the Spirit.ocx for the cybermaster, which works well. However, I recently bought a RIS2.0 set with USB IR-tower. To me it seems that you cannot program the RCX2.0 with delphi anymore. Or am I wrong? If so, more info please. Guido (25 years ago, 26-Nov-01, to lugnet.robotics)
 
  Testers/Evaluators wanted
 
I have two prototype/preproduction "devices" looking for a good home. 1. Generic RCX sensor adapter brick. This little 2x4 brick interfaces between the RCX sensor input and your own sensor design. It does all the hardwork, multiplexing the power and (...) (25 years ago, 26-Nov-01, to lugnet.technic, lugnet.robotics)
 
  Re: Extra 9V Motor
 
(...) (25 years ago, 26-Nov-01, to lugnet.robotics.rcx)
 
  Extra 9V Motor
 
Hi all, Where can I buy more LEGO 9V Motors? I cannot get it on legomindstorms.com and shop at home (LEGO). Yiu Thanks (25 years ago, 25-Nov-01, to lugnet.robotics.rcx)
 
  Re: Programming RCX using Delphi
 
(...) Hi Robert, Programming the RCX directly using Delphi is as simple as doing so with VB. Depending on the Delphi-version there are some problems to register the Spirit.OCX, because in the spirit.pas you have to change strings like while, if, on (...) (25 years ago, 26-Nov-01, to lugnet.robotics)
 
  Re: Lego light sensors
 
If you think only RCX Code is standard LEGO programming, I don't think you can dod it. But you can do it by NQC, RoboLab or legOS. Zhengrong --- (...) (25 years ago, 26-Nov-01, to lugnet.robotics)
 
  Lego light sensors
 
I was wondering if there is a way to do a comparison between two light sensor values using the standard Lego brick programming. Anyone know? Thanks! -Steve (25 years ago, 25-Nov-01, to lugnet.robotics)
 
  Vision command ActiveX component
 
I have tried to get the Vision Command ActiveX component from Kris Wauters web, but I've had no luck. His web (URL) seems impossible to get into. I have installed Macromedia Shockwave but that does not help (I get the errormessage: unable to open (...) (25 years ago, 25-Nov-01, to lugnet.robotics)
 
  Re: Programming RCX using Delphi
 
"Robert Linn" <robert@linnedv.de> wrote in message news:GnCrCr.9Cx@lugnet.com... (...) how (...) Spirit.ocx can be used just like any other OCX in Delphi. It will give you direct access to all of the methods that can interact with the standard (...) (25 years ago, 25-Nov-01, to lugnet.robotics)
 
  My RCX Infrared Expander
 
I have completed work on my RCX Infrared Expander. With $10 of easily found electronics components, you can this circuit that allows you to send an IR message from the RCX to trip an external relay. This allows you to control another output from (...) (25 years ago, 25-Nov-01, to lugnet.robotics)
 
  Re: Controlling HB using PC serial port
 
(...) I would posit that the easiest way is to use the serial cable. Then you don't have to do new cabling or only work with the digital pins which can also do output. Plus you're not spending your digital ports. You could also go through the SPI, (...) (25 years ago, 25-Nov-01, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR