 | | Re: RCX 2.0 Arrays
|
|
(...) Fixing that has been on the to-do list for a long time. But it just isn't a high priority since there are easy workarounds. Right now adding USB support is top priority. Dave Baum (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: tweaking around dlcd_show( )
|
|
(...) Ooops! I obviously wasn't looking at it properly last night (only browsing through the zip file). As 'dlcd_show' is defined as a macro that takes one parameter, but uses it twice to each of BIT_OF and BYTE_OF, which in turn both take 2 (...) (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Love the new Music capability with the new firmware!
|
|
(...) If you're using NQC and tell the compiler you're targeting RCX 2.0 (-Trcx2 for the command line version), then PlayTone() will accept a variable frequency. Duration, however, must still be constant. Dave Baum (25 years ago, 26-Aug-01, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 Arrays
|
|
(...) Manual? Manual! We don't need no stinking manual. Thanks, ("I guess I should read it", he says sheepishly) (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Building a peripheral bus from motor output
|
|
Hi all, I recently read an excellent paper by Fred Martin (of MIT fame) on building toys in a modular fashion. His microcontroller was similar to the RCX but had one key addition - a two wire serial bus so that active peripherals could be attached (...) (25 years ago, 25-Aug-01, to lugnet.robotics)
|
| |
 | | Serial LED is not lighting up during charger board assembly
|
|
I'm in the middle of assembling the Serial Interface and Batt. Charger board but have run into a snag. While testing the serial circuit, I was able to see the +-9V values on pin 2 of U16. However, when testing the transmit and receive functions of (...) (25 years ago, 25-Aug-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: bushing (bush) question
|
|
(...) No, I've found that all the half bushes share the same width: 1/2 stud. (...) Again, I've found that two old style half bushes together (with the tooth side facing each other), are _narrower_ than a full bush (or two smooth bushes). They are (...) (25 years ago, 25-Aug-01, to lugnet.robotics)
|
| |
 | | RE: Love the new Music capability with the new firmware!
|
|
Don't confuse the hardware version number (RCX 2.0) with the firmware version number. The 2.0 firmware has been available as part of the "2.0 RIS Beta SDK" download for quite some time from the Mindstorms web site. The 2.0 firmware can be downloaded (...) (25 years ago, 25-Aug-01, to lugnet.robotics)
|
| |
 | | RE: Love the new Music capability with the new firmware!
|
|
Don't confuse the hardware version number (RCX 2.0) with the firmware version number. The 2.0 firmware has been available as part of the "2.0 RIS Beta SDK" download for quite some time from the Mindstorms web site. The 2.0 firmware can be downloaded (...) (25 years ago, 25-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) RCX, (...) Coz, (...) to (...) Thanks, Jürgen! I have installed the firmware with a 9.6V=, 50mA! adapter, but no sensors or motors connected :-) It was a breeze after I found the right connection plates inside the battery bay. Gr., Remko (25 years ago, 25-Aug-01, to lugnet.robotics)
|