To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29109 (-10)
  Re: Programming VC
 
Hi Alberto, (...) No ! Every region is good for only one event. But you can build your own region to act like one with two events. You have to edit some bitmaps (as described here : (URL) ) Now, if you build a region (two in fact) with red and green (...) (25 years ago, 15-Jul-01, to lugnet.robotics.vc)
 
  Programming VC
 
I have some questions about programming VC. Is it possible to launch two differents events over the same region ? (i.e Do something if it detect blue and other thing if it detect red) Is it possible to combine events from differents regions ? I (...) (25 years ago, 14-Jul-01, to lugnet.robotics.vc)
 
  Re: RCX 1.0 polarity
 
(...) Um. None required. Um. Need to study AC current first. Um... AC doesn't have a polarity (well, it does, but it changes every 120th of a second...). Therefore, it doesn't matter _what_ polarity you put on the center pin. And, since there is a (...) (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  Spirit.ocx
 
Hi, Could someone please email me the spirit.ocx file? I'm am a legal owner of the RCX software, but I cannot find the CD. Thanks. (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  RCX 1.0 polarity
 
Hi! Does anyone know the polarity of the center pin for the AC jack on the RCX 1.0? Many thanks! Darc. (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  RCXCC and Scout
 
Hi group! Whenever I try to read the values of the Scout with RCXCC it only returns a value of -1. Diagnostics are fine. Is this a known problem or am I doing something wrong? Cheers! Darc. (25 years ago, 15-Jul-01, to lugnet.robotics)
 
  'Erase legOS' keystrokes - Please correct docs
 
The 'hold Prgm, and press On-Off' sequence does not work for me. It is necessary to press On-Off *twice* whilst holding Prgm.If someone is unlucky enough not to decide to just press random buttons for a while, the might not figure this out. Great (...) (25 years ago, 14-Jul-01, to lugnet.robotics.rcx.legos)
 
  About SensorValueRaw(SENSOR_3) in Scout
 
I tried to get raw value of sensors in Scout, the SensorValueRaw(0/1) is ok, I get the raw values of Sensor1 and Sensor2, but I found SensorValueRaw(2) doesn't work, no value is returned. Then I found a example in NQC Guide Version 2.3 r1, it is (...) (25 years ago, 14-Jul-01, to lugnet.robotics.rcx.nqc)
 
  Toolchain for Cygwin 1.3.2 (latest)
 
I have recently built binutils+gcc for the latest cygwin net release. I am investigating the possibility of posting them on the net, but I would like to decrease the file size as much as possible. I have already done 'strip -s' on the .exes, but I (...) (25 years ago, 14-Jul-01, to lugnet.robotics.rcx.legos)
 
  Re: Power and Reset
 
Hi All, Thanks for the good advice I got. I applied a separate power sypply to the board, to drive the motors and everything seems to go well now. I am not sure if I need to change the L293D for a more powerfull alternative. The chip driving both (...) (25 years ago, 14-Jul-01, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR