To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *28719 (-20)
  Re: problem with floating point numbers (legOS 0.2.5)
 
(...) You are the second person to report something like this, so there must be something wrong somewhere. I will take a closer look at this when I get a chance. I am busy until Tuesday though. I know I will forget, so keep e-mailing me until I fix (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx.legos)
 
  Re: IR Tower Use
 
(...) This isn't true at all. The tower converts an RS-232 serial transmission directly into IR and vice-versa. It is a pretty standard protocol. -Kekoa (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
 
  Re: IR Tower Use
 
(...) You can't really do what you are trying to do. The tower is designed to operate in request-reply mode. It sends a request, waits a few seconds, receives a reply during that time, then turns off. The idle state of the tower is off, and (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
 
  Re: Custom Firmware, IR Problems, and Dead RCXs (long)
 
(...) Maybe this is shedding some light on why LEGO removed the Power Port in the 1.5's. To remove a known problem without dealing with it.?.?.? Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
 
  RE: Custom Firmware, IR Problems, and Dead RCXs (long)
 
Even more interesting.... I've also just replaced the IRED I replaced a few hours ago in my RCX :-( This time, I'm putting a limiting resistor between the IREDs in the RCX to keep the current within limits. The following is pure conjecture on my (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
 
  RE: Custom Firmware, IR Problems, and Dead RCXs (long)
 
(...) Actually, there's a regulator on the Tower that takes the voltage for the digital side to +5 and keeps it there. The capacitor is only rated for 10V. The higher voltage will allow higher current through the IREDs as they are connected right to (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
 
  Re: Custom Firmware, IR Problems, and Dead RCXs (long)
 
(...) I'm pretty sure I know your problem to your number 2... The IR Tower has no protection against higher power. Running an unregulated power source into the IR tower is not a good idea! Use a 9v regulator package (The little 3 prong packages with (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
 
  Custom Firmware, IR Problems, and Dead RCXs (long)
 
The following information is my own opinion and not endorsed or verified in any way by LEGO. That being said, I think that now is the time to relate some experiences I've had over the past couple of months with my RCX and IR tower - and it boils (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
 
  Asking about Firmware (need help)
 
Dear All I`m a newbies in programming LEGO Mindstorms RIS. I have explored CD that embedded in my RIS KIT. Now i want to try make a user interface for LEGO Mindstorms RIS in my own language. I used microsoft visual c++ to build my software From the (...) (25 years ago, 26-May-01, to lugnet.robotics)
 
  Re: i neeeeeed help! can't logon to the lego site
 
(...) After moving to a new computer, Win98 and MS Internet Explorer 5.5 I found I could get into every site ...except... www.hp.com and www.kodak.com. On my old computer and Win95 no problem but consistent 'timeouts' on those two sites. I still (...) (25 years ago, 26-May-01, to lugnet.robotics)
 
  simpleRTJ servo or encoder code for HandyBoard?
 
Hi, I'm trying to use simpleRTJ on my HandyBoard with expansion board. The servo code needs some work as the servos chatter alot. Has anyone cleaned up the servo code? Also, I'm looking for code for encoders for the HandyBoard using simpleRTJ. Any (...) (25 years ago, 25-May-01, to lugnet.robotics.handyboard)
 
  Re: IR Tower Use
 
(...) Not really -- the tower uses its own proprietary communcations format. It's similar enough to that used by remote controls that learning remotes can pick up the signals, but I haven't heard of anyone going the other way around. (25 years ago, 25-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
 
  IR Tower Use
 
I know this may be a bit off topic, but didn't know where else to post, I own an IR tower and remote control, and was wondering if it is possible to use the IR tower for other things. eg using PC + tower to control stereo/TV, or using IR remote to (...) (25 years ago, 25-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
 
  Re: New Palm IR Software to remote control your RCX
 
I've been very interested in tightly coupling my Palm and RCX for over a year. Simply put, I want to have the Palm be a higher level 'brain' for my robotic creations, acutally being part of the robot. I use Forth for the majority of my Palm coding (...) (25 years ago, 25-May-01, to lugnet.robotics.palm)
 
  problem with floating point numbers (legOS 0.2.5)
 
Hi Here are two programs I've compiled and downloaded into my RCX. The first one works fine whereas the second doesn't (no music). Since the only difference between them is the type of the variable "number", I'm worrying about the ability of the (...) (25 years ago, 25-May-01, to lugnet.robotics.rcx.legos)
 
  Re: LVI install problems
 
Had an error "C:\Program Files\JavaSoft\JRE\1...1\Classes" is not a directory, but I just created a directory there and now it's working fine. Thanks!! (25 years ago, 24-May-01, to lugnet.robotics.rcx.java)
 
  Re: LVI install problems
 
At least it runs. :-) That error means that for some reason install could not create the directory .lvi in your windows directory. Check to see if you are able to create a folder in the Windows directory by hand, as this just calls "standard" java (...) (25 years ago, 24-May-01, to lugnet.robotics.rcx.java)
 
  Re: modulo in legOS 2.4 ?
 
-----Original Message----- From: Ciaran Jessup <ciaranjessup@myrealbox.com> To: lugnet.robotics.rcx....lugnet.com <lugnet.robotics.rcx...ugnet.com> Date: 24. mai 2001 22:39 Subject: Re: modulo in legOS 2.4 ? (...) an (...) you (...) ah, i mean the (...) (25 years ago, 24-May-01, to lugnet.robotics.rcx.legos)
 
  Re: modulo in legOS 2.4 ?
 
do you mean 3mod3 = 0 or mod(-3)=mod(3)= 3 ? If you mean the first then you want the %age operator, otherwise you want an 'abs' function not sure if legOS supports this as doesn't support floats(entirely), but you can always write a quick (...) (25 years ago, 24-May-01, to lugnet.robotics.rcx.legos)
 
  quad motor board for JCX (with Lego connectors) is out and works
 
Here are photos and schematics of our quad motor driver board for Legos and other small DC motors: (URL) board has been tested and is currently running a couple of MindStorms robots. We expect it to be featured in a keynote demonstration at JavaOne, (...) (25 years ago, 24-May-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR