 | | Re: Wishlist leJOS
|
|
(...) There still could be some special rom code that is called when the opcode is called for the standard firmware. Not very likely, but still possible. Andy -- See my Visual Interface for leJOS at (URL) (25 years ago, 22-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Transmit Frequency
|
|
Hello, My cybermaster (the tower) has two crystals 26.540MHz and 26.995MHz. Is your the same? Anybody got crystals with other frequencies? Lars Gertsen - Denmark (...) (25 years ago, 22-May-01, to lugnet.robotics.cybermaster)
|
| |
 | | Re: SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
|
|
(...) way I (...) four-wheel (...) 8-wheel (...) You drive all the wheels together in the same direction (first output), and use a motor to steer the front and rear groups in sync (second output). Is this what you mean? Very clever. You cannot steer (...) (25 years ago, 22-May-01, to lugnet.robotics)
|
| |
 | | R: c++
|
|
Thank you Pat! I should be able to make it go. I'll tell you the results in a couple of weeks, cause I have to finish another project on lnp first. I still don't understand much the unix community: if version 2.5 is to be patched anyway, why not (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) Remember that Lejos is replacement firmware, the OP codes no longer exist as they are part of the standard firmware. Regards Gordon (25 years ago, 22-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: RCX motor pulsing
|
|
I have controlled LEGO trains via the RCX many times. The question is how to control the speed of the train under a finer ganularity then just the native power levels. snip ...this comment has promise! Can you vary the width of the pulse? <The good (...) (25 years ago, 22-May-01, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) I think that the datalogging area is just a special limited firmware array, but , IIRC, since it mentions nowhere that you have to remember to keep the datalog size into account. Try using the opcodes, and see what works. Andy -- See my Visual (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: High Strength Powered Steerable pivot wheel
|
|
(...) Well I feel a total fool, sorry Steven. (Embarrassment tempered by the fact that you can still get them.) (...) Here's the original post about this... (URL) (must remember to switch brain on while at work in future) (25 years ago, 21-May-01, to lugnet.robotics)
|
| |
 | | SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
|
|
(...) In the near term, I've opted out of the "steer in place" requirement. That way I go from four outputs to two. With an 8-wheel SHRIMP, I steer like a four-wheel steered (FWS) car does at low speed. Also, I don't have to worry about the friction (...) (25 years ago, 21-May-01, to lugnet.robotics)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) It does answer my question, but I was thinking that a feature like that would be more memory efficient. It seems to me (knowing very little of programmimg small devices) that there are special OP codes (looking at Keokea Proudfoot's RCX (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
|