To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2861 (+10)
  Handyboard Projects
 
Ben Zorn of the University of Colorado/Boulder presented a paper last Wednesday, 15 Oct 97, at the Telemanipulator and Telepresence Technologies IV section of the International Symposium on Intelligent Systems and Advanced Manufacturing in (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
 
  Re: Board synch problem
 
I've noticed the only limited success I've had downloading pcode_hb.s19 is - with older slower systems that have _no_ modem cards installed using dlm - with win95 or win311 systems using hbdl with no modem cards as well. The hbdl downloads them (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
 
  Re: Board synch problem
 
I'm not sure if my follow up message made it, appears to have bounced. Just in case, the problem resolved when I took out the modem and network cards. Interestinly, the handyboard battery was nearly discharged when the problem surface. The cards had (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
 
  Re: Board synch problem
 
two things you can try: 1. use DLM to download the CONFIG0C.S19 file. Make sure to use the -eeprom flag. This will cause it to burn the config register to the proper value. 2. Have you tried Randy Sargent's DL.EXE for DOS / Win 3.1 full screen DOS (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
 
  Re: Board synch problem
 
Fred et.al.: Success! DLM, DL, and the others just wouldn't work for any of my hardware, but a colleague wrote a shareware application ( LOADHC11.EXE ) expressly to load bootstrap 256 byte loader program into page zero of internal RAM , including (...) (29 years ago, 20-Oct-97, to lugnet.robotics.handyboard)
 
  Robot
 
Greetings, Just an FYI for everyone, I noticed a promo on the Discovery Channel that will feature a small robot. Strangely, the segment is to feature deformed frogs also. Not quite sure what the connection is , but....It was advertised to air (...) (29 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
 
  AD: Wirz Electronics
 
Hello Everyone, We have a number of new Microcontroller products that we think you may be interested in: ---...--- Microchip PIC Products: "Programming and Customizing the PIC Microcontroller" book by Myke Predko (URL) Up The Pace" book by David (...) (29 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
 
  Digital Ins and Motor Outs
 
I have succesfully loaded pcode_hb.s19 and run IC with my Handyboard (finally). However, I am having a few problems with the digital inputs and the motor outputs. The Start and Stop buttons work fine when testing the digital inputs using the (...) (29 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
 
  Rob Gaunts Last Message
 
I sent out a message few minutes ago listing all sorts of problems I was having. Don't worry about it. I just figured it all out. I was using lib_r22.lis instead of lib_hb.lis in IC. Now things are working fine except that the voltage at pin 8 of (...) (29 years ago, 22-Oct-97, to lugnet.robotics.handyboard)
 
  Re: Rob Gaunts Last Message
 
(...) the instructions are wrong -- you should be seeing about 9v, which is the voltage on the nicad pack. i will revise the instructions. thanks for pointing out the problem. fred (29 years ago, 22-Oct-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR