To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27909 (-10)
  Re: dll problems
 
Nevermind, I figured it out. Apparently some of the programs weren't compiled correctly in the demo folder because some of them worked and some didn't. I was able to recompile some of them and then they would download. Wierd but at least I figured (...) (26 years ago, 8-Apr-01, to lugnet.robotics.rcx.legos)
 
  Re: Revisions to RcxCC
 
Works great! Nice to see the Scout support. (...) (26 years ago, 8-Apr-01, to lugnet.robotics.rcx.nqc)
 
  Re: Length of Diagonal Spreadsheet
 
(...) Thanks for the link to your gear spacing site. That is sort of what I was looking for though in my chart I aimed at being more general then just a list of workable gear spacing. My diagonal measurements can also be used to find workable beam (...) (26 years ago, 8-Apr-01, to lugnet.robotics)
 
  Re: Length of Diagonal Spreadsheet
 
(...) ---...--- snip ---...--- (...) Gus I can't download the sheet nor can I open it online. If you can email it to me I can convert and return the pdf via email, providing the document isn't too large for your mail box. Dave (26 years ago, 7-Apr-01, to lugnet.robotics)
 
  Re: A couple of questions
 
(...) Only by the vocal majority, I think. There has been a recent thread about a sub-group (cult?) of "grinders". I say the end justifies the means here. You might look into FischerTechnik (my spelling may be off). Someone on this newsgroup did (...) (26 years ago, 8-Apr-01, to lugnet.robotics)
 
  Re: Length of Diagonal Spreadsheet
 
(...) Er oops :) that's a 2L spacing, same as 24T to 8T or 16T to 16T. (26 years ago, 8-Apr-01, to lugnet.robotics)
 
  Re: Length of Diagonal Spreadsheet
 
(...) I'm assuming he's talking about the 12T double bevel gear. Three sets that I know of that have them are the DDK, the Technic 8448 Super Street Sensation and the Technic 8008 Stormtrooper. They have a standard 3L mesh spacing when used with a (...) (26 years ago, 8-Apr-01, to lugnet.robotics)
 
  Re: Length of Diagonal Spreadsheet
 
(...) For gear spacings, you might try: (URL) My testing shows that errors as great as 5% are usually no problem for (...) That *can't* be right. The tolerable error for two 40t gears is no different from the error for two 8t gears - so it's (...) (26 years ago, 8-Apr-01, to lugnet.robotics)
 
  New version: MacNQC 2.2.1
 
Hi all, I have just uploaded a new version of MacNQC. Version 2.2.1 is a minor release based on 2.2 and only changes the compiler from 2.2r2 to 2.3r1 and fixes a crash on older Power PC machines. Version 2.2 updated the text editor to WASTE 2.0. (...) (26 years ago, 8-Apr-01, to lugnet.robotics.rcx.nqc)
 
  Re: program wont stop running
 
(...) If the person stops running, then that means the program has stopped. The "Run" button stops a program and turns off the motors. However, when a program finished normally (with nothing more to do), the motors are left in whatever state the (...) (26 years ago, 8-Apr-01, to lugnet.robotics, lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR