To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27624 (-20)
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
I drilled a hole in a 1x2 brick to give the light sensor a better sense of direction and to block the LED. The goal was to have the light sensor seek an IR beacon. (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
 
  Re: lego cap, polarity, etc
 
No. DO NOT UNDER ANY CONDITION CONNECT AN ELECTROLYTIC (ie one with +/- on the terminals) IN REVERSE. The electrolyte is a high resistant in one direction only. The other direction is nearly a short. You may end up hurt as the capacitor blows up in (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: lego cap, polarity, etc
 
(...) A couple of comments on this... An 'inverter' with respect to DC creates AC, it doesn't swap polarity. If you're going to use the term correctly always use 'invert polarity' and never 'invert' by itself. If you go into a store and ask for a (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Neural network for legOS... ??
 
(...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
 
  May I use RCX to play a .wav file?
 
I want to know if I can use RCX to play a .wav file, does anyone help me? Br Zhengrong (26 years ago, 29-Mar-01, to lugnet.robotics.rcx)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
As an alternative method to tubing, you can use an IR filter (black inversible film) as described on my page : (URL) doesn't work with Lego visible lamp though... Philo (URL) (26 years ago, 29-Mar-01, to lugnet.robotics)
 
  Re: Lego accessories for the photographer
 
(...) Sort of... I borrowed the older Coolpix 900 I have at my office ;o) It is quite good for the kind of resolution needed for the web ! Philo (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
 
  Re: Robot navigation - barcode stations?
 
I think it's an excellent idea... I saw the barcode system being explained some years ago and I still think it can be the most accurate. One thing that's different in the system I saw was that there were no LED's used (not needed...) and it would (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx)
 
  Ser. Col. Only!! I'll cover shipping!!
 
(26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
 
  Serious Collectors Only!
 
I'm selling my entire collection for $4,500. There are over 300 sets MISB, and over 200 sets opened but still in mint condition. Over 90% of the opened sets were put together once; and then sealed in zip-lock bags. The boxes of the MISB sets are in (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
 
  Unsubscribe
 
Sorry, I knew I shouldn't post this but I can not unsubscribe to this newsgroup. I have tried to stop this by going through the option and it doens't recognize this subscription. Please take t-f-l-y@home.com out of you system. Thanks (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) You can find light sensor schematics on Michael Gasperi's page: (URL) Using the RCX IR emitter as the illumination source. Don't know (...) Someone has already tried this. You can check Simen Svale Skogsrud's page for an example, with NQC (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Assembly in my C-program
 
(...) If you want to drive directly the motors you should first disable motor handling in legOS (remove CONF_DMOTOR definition in config.h). Then you can create a high priority task that switches motors on and off writing in the motor output port. (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Assembly in my C-program
 
(...) pulses (...) at (...) would (...) Hmmmm. This should be possible, but it's a bit more tricky with stepper motors - you have to allow for the speed-up and slow-down. Thus just calling motor_speed(50) would have to initiate a task that starts (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
Ralph Hempel had an example of the heat-shrink tubing solution here: (URL) also tried used some black vinyl from a binder? -Tim (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
To make a passive light sensor, you can use a design like Michael Gasperi's: (URL) costs only a couple bucks, and works quite well. If you would like better response from your lego light sensor, you can use a piece of black shrinkwrap tubing and (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
Hi Chris, You can turn off the LED with software though you may be a little disappointed with the light sensitivity. The reason the LED is on is because your program has set the sensor to an active sensor. If you set the type to NONE make the mode (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) Maybe. I think RCX2 with NQC has some crude arrays, I haven't looked into them yet, but I might be able to use them to do simple mapping on the RCX. Or something even cruder if I don't have arrays. (...) Ahh. Hmm. I wonder what it actually (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
This sounds very cool. If you want to do the mapping at the bottom, you will have to use alternitive firmware anyway (right?), and they have a passivate command that turns off the light. It passivates the sensor, but I don't think standard firmware (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Shutting off illumination LED on Light Sensor for LIDAR
 
Has anyone successfully found a way (short of paint, or cutting internal wiring) of shutting off the red 'supply light' LED on the Lego light sensor? The supply LED is great for active-detection situations, like line-following, when you need to (...) (26 years ago, 28-Mar-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR