 | | Re: US S@H Specials, Feb 28 - Mar 06, 2001
|
|
(...) <lugnet.robotics.rcx...ugnet.com> (...) they are (...) a (...) the (...) (URL) (...) Okay that clears that up. Still need to find 1 x 7 lift arm as well as 1x8 and 1x6 plates. Alan (26 years ago, 28-Feb-01, to lugnet.robotics)
|
| |
 | | Re: US S@H Specials, Feb 28 - Mar 06, 2001
|
|
Well, that certainly does not have the right piece(s)! Thanks for the search. So I still need to find Technic liftarm 1 X 7, and Technic plate 1 x 8, and 1 x 6... (...) 7" (...) (URL) > (...) <lugnet.market.shopp...ugnet.com> (...) (26 years ago, 28-Feb-01, to lugnet.market.shopping, lugnet.robotics)
|
| |
 | | Re: NQC 2.31b 1 and the RCXcc
|
|
Gus, Bob, Mario, and all, Yes, I was able to edit the C:\autoexec.bat with the line: SET NQC_OPTIONS=-TRCX2 I did not put in the second line SET PATH=c:\dev\lego\nqc;%PATH% because (a) I was not sure where to type it, and (b) I do not think I need (...) (26 years ago, 28-Feb-01, to lugnet.robotics)
|
| |
 | | Re: US S@H Specials, Feb 28 - Mar 06, 2001
|
|
Searching lugnet found the following: (...) (26 years ago, 28-Feb-01, to lugnet.market.shopping, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: NQC 2.31b 1 and the RCXcc
|
|
Hi Alan, Try sysedit like Robert Fay suggested. But I think that you will need to make sure RCX2 is all uppercase. In otherwords, add the line: SET NQC_OPTIONS=-TRCX2 The other line that I have in my autoexec.bat that is related to NQC is: SET (...) (26 years ago, 28-Feb-01, to lugnet.robotics)
|
| |
 | | Re: US S@H Specials, Feb 28 - Mar 06, 2001
|
|
----- Original Message ----- From: "Alan Carmack" <amenpage@earthlink.net> To: <lugnet.market.shopp...gnet.com>; <lugnet.robotics.rcx...ugnet.com> <snip> (...) It looks to me that these last two pieces aren't offset by 1/2 a stud, they are sitting (...) (26 years ago, 28-Feb-01, to lugnet.market.shopping, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: US S@H Specials, Feb 28 - Mar 06, 2001
|
|
Does anybody know what is in Technic Set 5291--Liftarms&Triangles? I am specifically looking for some piece(s) dubbed "Technic Liftarm 1 x 7" (32065.DAT?) so I can build the small killough platform as shown on (URL) where can I get such a piece, and (...) (26 years ago, 28-Feb-01, to lugnet.market.shopping, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: NQC 2.31b 1 and the RCXcc
|
|
Windows 98: From "run" type "sysedit", this will open several files for editing. The top file is Autoexec.bat Type SET OPTIONS_NQC=-Tcrx2 and save the file. I don't know if this is good in Win ME -- Bob Fay rfay@we.mediaone.net (URL) Carmack" (...) (26 years ago, 28-Feb-01, to lugnet.robotics)
|
| |
 | | problems installing LNP
|
|
have downloaded dllx.tgz, lnpd+liblnp.tgz and lnpd.static have unpacked them into the $HOME/legos/host directory in lnpd+liblnp i have: make realclean make depend make all good so far in dllx i have: fixed the Makefile so that: (...) (26 years ago, 28-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: NQC 2.31b 1 and the RCXcc
|
|
I am responding to both Mario and Gus in this one post. I am trying to update my RCXcc so it can use the newer versions of NQC and RCX2 under Windows ME. Mario writes (...) must (...) Uh, I am using Windows ME, so I went to Control Panel and then (...) (26 years ago, 28-Feb-01, to lugnet.robotics)
|