 | | Pic board onto handyboard?
|
|
Dear Handyboarders Some time ago I bought a toy that runs off 2 - 1.5 volt batteries. The controller board has a PIC on it, control of the toy was via a TV remote, and it ran two separate motors for the drive train. There is also an on/off switch. (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
I have a question to ask I want to use two 16V (maybe a bit more) motors and one 9V the question is To use either an Opto Darlington Isolator that my supervisor knows about, which uses the digital outputs where they are just switches or to cut the (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | motor drivers
|
|
Hi all, I suppose that this is really a Mini Board quesiton, but it involves L293D motor drivers, so here goes. The Mini Board manual says that the MB accepts DC power supply of 6-36V. I was using power ranging from 25-32V to run one, and the L293Ds (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pic board onto handyboard?
|
|
(...) Hello Michael I might be able to help you out a bit! I think that the toy you are talking about is featured in the March 1996 issue of Electronics Now mag (cover page) It describes how to build a runabout Robot controlled by a Sony compatible (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | Re:
|
|
(...) Check out Dave Chu's robotics and electronics page @ (URL) has schematics for what you are looking for! Hope this helps. Laz (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
German Pablo Gentile German Pablo Gentile Systems Engineer. Electronics Expert. (really??? ;>) ) ggentile@cvtci.com.ar (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
I have write a code for manipulate the LCD in the handy board. Because i can't use a battery backed RAM, i need to write in assembler. Well , i'm really read all the FAQ for LCD and for Handy board (including the apendix B for the 6270) .I'm using (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | Serial routines
|
|
Has anyone used Richard Drushel's math and serial libraries with a real serial port? The HB seems to miss about every other character when I use any of the higher level functions. Thanks, Jodi Graf (29 years ago, 4-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Suppliers in Germany ?
|
|
Hello, here is a list of suppliers in Germany. It's an Excel-sheet and I've attached it to this mail. I hope you can use this list. If you have any further questions you can send me an e-mail directly. Steffen. (29 years ago, 4-Sep-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
I'm able to compile version 2.861 with Kent Farnsworth setup, but not ver 3.1 of the P-code. Has anybody been able to do this? I get a lot of phasing errors when I try. There is a problem with the current LCD initialization routine I would like to (...) (29 years ago, 4-Sep-97, to lugnet.robotics.handyboard)
|