 | | handy board code
|
|
Hi, I am a begginer programer and I'd like to know if there is anyone out there who has written code for there handy board bot that I could get and learn from? I have all of libraries from the HB site, but nothing that does a full routine that I can (...) (26 years ago, 13-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: bug fixes
|
|
(...) My web page at (URL) This is for DJGPP, not Cygnus. Rossz (26 years ago, 13-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | LegOS and the Downloader....
|
|
I just installed LegOS last night, made my first few not-too-complicated programs today, and downloaded them. They worked fine, up until I found the bugs. I tried to download a new, updated version of my program, and got an error message. (26 years ago, 13-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: bug fixes
|
|
Paolo Masetti <paolom@pragmanet.it> wrote in message news:G8o1Fv.2uG@lugnet.com... (...) Well, I'm looking to set up legOS on my new (dual-boot) laptop, so it may be a good chance to check out the Windoze development environment. Where can I get (...) (26 years ago, 13-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Rope Climbing and Can Crushing at BrickBots.Com
|
|
Doesn't a machine that does nothing score perfectly? If so, my entry is an RCX sitting next to three cans. It finishes the instant it starts. You have a formula time * height * bonus = score, with small being better. So a robot that does no crushing (...) (26 years ago, 13-Feb-01, to lugnet.robotics)
|
| |
 | | 3 Sharp GP2D12 using one input port !!!
|
|
Hi all, It's done. I've got 3 Sharp GP2D12 Infrared Ranger with my RCX using only one input ! I use Michael Gasperi's Multiplexer ((URL) his more general analog interface (3 times ; the one with the opamp) ((URL) a 9 volts battery (6LR61). (Thanks, (...) (26 years ago, 13-Feb-01, to lugnet.robotics.rcx)
|
| |
 | | RE: A dream Mindstorms/Technic piece...
|
|
The Mindstorms touch sensor isn't a switch, but a sensor. You need an RCX or MicroScout to read it's status. It is not suited for directly switching a load like a motor. It can only carry a very small current, and still has a lot of resistance when (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Rope Climbing and Can Crushing at BrickBots.Com
|
|
Hello All, On Friday February 9th, 2001 the Rope Climbing Contest at BrickBots.Com finished with three completed entries and one standout winner! The contest objective was to build a LEGO robot to go up and down a length of rope as quickly as (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Re: bug fixes
|
|
(...) from (...) has... (...) :-) Hi. Here I am. No sea waves, sorry... ;-))) Only a lot of work and two sons :-). I'm actually working in finalizing cygnwin 1.1 instructions (if someone want to test them let me know). My beta testers are a bit slow (...) (26 years ago, 12-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: A dream Mindstorms/Technic piece...
|
|
Jennifer Clark <jen@vulture.dmem.strath.ac.uk> wrote in message news:3A87CF43.4C05B6...h.ac.uk... (...) the (...) a (...) some (...) battery (...) One possibility may be to use a Mindstorms touch sensor to switch it on/off. This would remove the (...) (26 years ago, 12-Feb-01, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: OmniRemote Update part II (brief)
|
|
(...) Unfortunately, I have no RCX as of yet - been too busy buying car parts. however, I don't think he's worried about firmware right now, and more worried about just sending basic messages back and forth. Firmware comes later, and I suspect it (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | leJOS article in JavaWorld
|
|
Enjoy! (URL) (26 years ago, 12-Feb-01, to lugnet.robotics, lugnet.robotics.rcx.java)
|
| |
 | | Re: What kind of plastic?
|
|
PVC pipe cement is the easiest kind of glue to get hold of for gluing Lego bricks. It is "VERY" effective. Use a tooth pick to apply it - you don't need much! As far as axles and other axle related parts, they are made of something quite different - (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Re: A dream Mindstorms/Technic piece...
|
|
(...) I'm sure it is possible, as the switch on it is also spring loaded and has a "motor on but switch not locked in place" setting. You'll still have to do some lego modification by soldering at least one other cable directly to the battery (...) (26 years ago, 12-Feb-01, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: legOS
|
|
(...) How would you tell NQC to use COM2? like this? NQC -s COM2 or somthing like that? (26 years ago, 12-Feb-01, to lugnet.robotics.scout)
|
| |
 | | Play pcm on the RCX
|
|
I think this item has been discused sometimes but I have discovered RIS, just last Christmas. Has anyone played a pcm wave? I know how to play it on a PC speaker, but I don´t know a lot on H8 architecture and so on the timers (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Is an RCX Output Amplfier, possible ?
|
|
(...) Actually, you need four transistors in what is called an H-bridge configuration. This is due to the fact that the motors are usually intended for bi-directional use. If you are only using them in one direction, a single transitor will suffice. (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | POPTRONICS isn't worth it
|
|
For those of you who have seen the March 2001 issue of Poptronics (the "Special Robotics Issue") and been attracted by the words "Lego Mindstorms" in bold type one the cover - believe me, it isn't worth it. In the finest traditions of Popular (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Underwater Sensors
|
|
(...) First off, beware that ordinary tap water contains dissolved impurities and is electrically conductive. (Water itself, BTW, is actually an insulator - it's the dissolved impurities that give it conductivity). It usually isn't an issue with (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Walkers
|
|
Thanks for the feedback people. I asked the question because I have been working on a walker for around 6 weeks, and was getting a bit discouraged. I have since had some success on the weekend. My walker will now go through it's complete walking (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|