To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *26494 (-10)
  Re: Pneumatic tubing...
 
(...) Has anyone tried the tubing from Pitsco/Dacta? See: (URL) It has a 1/8" ID and a 100 foot roll is $9.00. Is it like the tubing in Pneumatic sets or is it a hard plastic tubing instead of rubber? Thomas (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Pneumatic tubing...
 
(...) I believe that TLC has used the same tubing in a few non-pneumatic sets. I have one older pneumatic set here so I took a piece of tubing off of it and compared to some pieces that came off of the 6180 Hydro Search Sub. They appear to be quite (...) (26 years ago, 2-Feb-01, to lugnet.robotics)
 
  Re: Short Circute Problem -- EMERGENCY
 
Hi guys , i tried all the tests mentioned in the HB assembly to find out which part of the HB blown. No luck. i am giving the results here: 1) Tested the interface and charger board - looks good. (Both power supply and the MAX232 circuit) 2) Tested (...) (26 years ago, 2-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Pneumatic tubing...
 
(...) the (...) Heck, ya got me ;-) Could be rubber, extremely soft polyurethane, or any number of compounds. You'd probably have to ask someone at TLG to identify it. I just bought a few packs of tubing from S@H to make sure I had enough. I get it (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  Re: Pneumatic tubing...
 
Dear Tom (...) it should have been in my original post) is the *material* and *x-sectional dimensions* for the LEGO pneumatic tubing. I have several sources for different kinds of tubing, but I want to get something as near identical to the LEGO (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  Re: Visual NQC 2001
 
<Runtime error 380 fix If you get Runtime error 380 during compile start you need to change the subdirectory where NQC.exe is stored. Use a directory without a space in the name. Example C:\NQC\nqc.exe This will work.> That did not work. I am still (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: Anyone using Mac beige G3
 
(...) One thing to keep in mind about Mac serial ports is that they are not RS-232, rather they are RS-422. IIRC, RS-232 is a singled-ended voltage standard (ref to ground only), where RS-422 is a differential standard. The 'common' method of using (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
 
  Re: Pneumatic tubing...
 
(...) I suppose you could check medical supply shops... You could also try www.newark.com, and request a catalog. If you are using Netscape Communicator, just type "pneumatic tubing" (without the quotes) into the URL field, and start with those (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
 
  RE: 68HC11 (Evaluation Board)
 
I was wondering if anyone was aware of any pre-existing library calls that would allow an individual using an Evaluation Board (EVB-68HC11)+ Buffallo Monitor(ImageCraft C v5.0) to access the system clock. I've noticed that with using Interactive C (...) (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Pneumatic tubing...
 
Dear Tom (...) Thanks for your reply. You'll notice that I mentioned in my original question that the tubing available in the RC shops (which I referred to as poly tubing rather than neoprene -- my bad) is a bit stiff. I had a vague memory of (...) (26 years ago, 1-Feb-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR