 | | RE: Rotation Contacts
|
|
Don't forget that the turntable has a very large hole in the center. You can run all kinds of things through this hole. That gives you a couple of alternatives: - You can run the wire for the motor through the large center hole of the turntable. (...) (26 years ago, 4-Jan-01, to lugnet.robotics)
|
| |
 | | Rotation Contacts
|
|
Has anyone ever tried to make a set of electrical contacts that allow rotation? What I want to do is have an electric motor on my crane using the large turntable from 8480 but I don't want a flopy wire in the way of rotation. Any ideas or thoughts (...) (26 years ago, 4-Jan-01, to lugnet.robotics)
|
| |
 | | Star Wars ATAT-walker in Holland
|
|
Hi, Does anybody know where I could buy the Star Wars ATAT-walker in Holland? I haven't seen it in any shop, except for the online one :) I would really like to see the box and take a look at the contents before I actually buy it. That's why I (...) (26 years ago, 4-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Positioning with the RCX - a pragmatic approach
|
|
(...) I have seen a nonlego robot called Cye. He is controlled by a human on a computer. As you move him about a room, he uses a computer program and a bump sensor to make a 'map' of the room. After the map is made, a homebase can be set up, and (...) (26 years ago, 3-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Cybermaster ? What and where is it?
|
|
(...) Sorry to tell you, but the Cybermaster is only sold in Europe (AFAIK). The used RC tower is not certified for distribution in the US. The model is sold here (in Germany) for around $75 if you accept a slightly damaged case. cu Harald (26 years ago, 3-Jan-01, to lugnet.robotics.cybermaster)
|
| |
 | | Re: IR to Radio
|
|
While observing this thread slowly unwinding here, I would like to point out that the PC/RCX communications is bi-directional making such things as remote control extenders not really applicable. I would like to hear about other people's experiences (...) (26 years ago, 3-Jan-01, to lugnet.robotics)
|
| |
 | | Re: IR to Radio
|
|
(...) Radio shack used to sell some which looked like little pyramids with a telescoping antenna; They were about 4" tall and 3" square at the base. The power supply was something like 9V, I don't know how many mA. (26 years ago, 3-Jan-01, to lugnet.robotics)
|
| |
 | | Re: reading sensors on CM
|
|
Hi :) [Note1: CM = CyberMaster; pBrick = { CM | RCX | Scout | RCX2 } ] [Note2: I think this could be usefull to others = CC:lego-robotics] [Note3: I'm showing source code done by Mark Overmars = CC:markov+lego] Well, all my PC apps were done with (...) (26 years ago, 3-Jan-01, to lugnet.robotics)
|
| |
 | | Positioning with the RCX - a pragmatic approach
|
|
THE QUESTION ... ... how to determine and measure a position in a room? This question was raised several times in LUGNET (e.g. Kris Zabriskie) and caused some discussions. As it has been stated, this simple sounding task is not at all trivial and (...) (26 years ago, 3-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Use for Bad Lego Motor
|
|
Even i have 3 motors that hardley move by hand I'm in india and i brought this kit and extra motors 1 1/2 years back ,, but i thought that as i just kept it like that and did not use it it got stuck . I never knew lego supplies bad motors ,, does (...) (26 years ago, 4-Jan-01, to lugnet.robotics)
|