To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *25704 (-10)
  Robosports Instructions
 
Hello all, I'm Peter. I have RCX 1.0 with mains adapter (from maplins, works great!) and Exploration mars, also Ultimate accsessory set (the remote rocks). I also have many other lego parts, and whish to make some robosports models, I have extra (...) (26 years ago, 3-Jan-01, to lugnet.robotics)
 
  Re: Use for Bad Lego Motor
 
(...) It should spin easily with just fingertips against the cross-axle. It should continue spinning several rotations on its own inertia from a fast initial spin. (26 years ago, 3-Jan-01, to lugnet.robotics)
 
  Re: Use for Bad Lego Motor
 
(...) Wait until after you get the new motor from LEGO. Sometimes they WANT the old motor back. I seem to be the king of bad motors. (7 at last count out of 16) All DOA. Lego has asked for about half of them back. I have one motor that spins fine (...) (26 years ago, 3-Jan-01, to lugnet.robotics)
 
  Re: Power inlet to RCX 1.5?
 
(...) Short answer is yes. Check out this thread at Lugnet: (URL) 2) 130mA. Is that enough? I'm not sure how the RCX works internally, but the (...) Short answer is no. A single motor can draw 100mA. (26 years ago, 3-Jan-01, to lugnet.robotics)
 
  Using laptop IR Port instead of the IR Tower
 
Hey folks, Has anyone been able to use a Thinkpad IR Port to talk to the RCX? I have been programming the RCX using spirit.ocx. All is well with the IR Tower connected to a serial port. I would like to get rid of the IR tower and use the built-in IR (...) (26 years ago, 2-Jan-01, to lugnet.robotics)
 
  Re: Help! I think I nuked my IR transmitter!
 
John Phillips here, I hope this comes out on the correct thread. I'm not quite sure how to post replies, if it does't any help on how to post replies would be appreciated. Monday after reading a few suggestions I thought I'd try again, well this (...) (26 years ago, 3-Jan-01, to lugnet.robotics)
 
  Re: Power inlet to RCX 1.5?
 
(...) The motors without any load don't draw much current. I guess that 130mA is not enough if you really make them work hard. Jürgen (26 years ago, 2-Jan-01, to lugnet.robotics)
 
  Use for Bad Lego Motor
 
The new Mindstorms RIS 1.5 set I gave my son for Christmas had a bad motor right out of the box. The motor is just jammed up and will barely turn by hand. I emailed Lego and they are sending me a new one (in up to 3 weeks!). We couldn't wait to get (...) (26 years ago, 2-Jan-01, to lugnet.robotics)
 
  Palm Pilot & Scout
 
I heard that it was possible to control the Scout with a palm pilot. How is this done? Thank You, Greg Ericksen (26 years ago, 2-Jan-01, to lugnet.robotics.scout)
 
  Re: Motor Speed Code
 
Contact the 68332ABB site at www.egroups.com and sign on to the list server. Kenneth Maxon has done a lot of work with this kind of thing, and is a member. It's basically a no-brainer. Best regards, Gary Livick (26 years ago, 2-Jan-01, to lugnet.robotics, lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR