To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2566 (+10)
  Re: 3v motors
 
If you try to regualte the voltage to 3V You will still loose the extra power as in using a resistor. You lose it in the form of heat to be specific. Using a regulator will give you the 3V you need at continuous output. I'm not sure how voltage (...) (29 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
 
  Re: Obtaining the Handyboard in the UK
 
(...) I too talked to Customs and they are typically confused and confusing about import tariffs and such. I was told that the limit was £19 for what that is worth. I would probably just order the damn thing and see what happens. Tax probably won't (...) (29 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
 
  Re: 3v motors
 
With the modification mentioned in the the FAQ, can you power 3V motor at 3V with external power? The FAQ mentions external 6-36V and L293D spec sheet says that the minimum Vs is Vss (which has a minimum 4.5V). The modification doesn't change Vss, (...) (29 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
 
  Hong Kong
 
Hi, As an additional note about buying the HB from Hong Kong, be on the lookout for wire fees or bank draft fees. I have just purchased an HB and the price is indeed good, but I also had to pay a $12-$20 fee for getting the funds to Hong Kong. The (...) (29 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
 
  Re: 3v motors
 
Yes Vs should stay at 5v, but if you read my original message the best thing is to use 9.6 volt motors!! Save yourself some trouble! jm (...) (29 years ago, 7-Aug-97, to lugnet.robotics.handyboard)
 
  Obtaining a Handyboard in the UK
 
I just wanted to say that I ordered the HB from Hong Kong on Monday. I sended the money via my bank account and paid £12 for money delivered in 5 working days, or £17 for two. It containes: Kit A DB-9 or DB-25 (please select one of them, this (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
 
  Re: CdS cells
 
David, I believe you will want to purchase ones that have a dark resistance more than say 20K. The sensor is part of a divider circuit that includes a 47K resistor. The sensed signal equals (sensor resistance)/(sensor +47K) multipled by 255. If your (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
 
  Servo as drive motor
 
Hello, I have modified and connected 2 servo motors to the handy. The speed of one is much slower than the other. I swiched the motors around (first in Port (0),and (2) ) and then the reverse and the same motor is slower ... could I have fried the (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
 
  Re: CdS cells
 
(...) It's certainly easiest to start out with a sensor that has a reasonable resistance range. However, if for whatever reason you have sensors that tend to be lower in resistance to the ideal, simply add your own resistor between the signal and (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
 
  Re: Servo as drive motor
 
(...) I'll try to replace the caps and see if there is an improvement. I was thinking that when I melted the new leads to the motor I may have left the iron on it for too long, thus burning up the caps. I'm going over to my dad's shop to work on (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR