 | | Re: servos?
|
|
(...) Phil, Have you tried this site: www.robotstore.com ? They have servos in discount packs as well as serial controllers for them. Cheers Massimo Piccoli -only wanting to know something new puts you a step forward- (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: servos?
|
|
The best places are the mail order hobby stores. They have the widest selection of servos and very good prices. The two I recommend are Tower Hobbies (www.towerhobbies.com) and Hobby Shack (www.hobbyshack.com). Either of these sells servos cheaper (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Voltage problem
|
|
Well, further experimentation revealed that the chips are working, but with a quirk: If the the input of the '232 (pin 10) is tied to ground (pin 15), then the output (pin 7 of the '232, or pin 3 of J9) goes to the expected value of ~+10 volts. If, (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RC bot base
|
|
Hello All, I have just purchased a new TYCO 9.6V Zig Zag car. It seems to have a fairly good base w/treads. I connected it to the handyboard (after gutting it and extending the wires ). Next I gave the motors a test and they both ran way too fast. (...) (29 years ago, 1-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | int/float to string routines?
|
|
Are there any int/float to string conversion routines available for the handy board? I'm sending data over the HB's serial port to my PC, and I need to be able to send data in string format. (I was originally sending data in its actual byte value, (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: int/float to string routines?%nu
|
|
[Jeff Keyzer] spake unto the ether: (...) Look at my serial I/O routines (Fred has them on the HB ftp/website with the other user-contributed software), specifically the functions in conio.c and serialio.c. I have both float-to-ASCII and (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | RV: What is the better way to comunicate handyboard???
|
|
---...--- (...) the (...) help (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Exp Board ETA?
|
|
Dear all, I must apologize for the long delay and stringing everyone along waiting for the Expansion Board. Even now I hesitate to answer for it is not pleasant to have nothing to show presently. Currently, I am working on the "Advanced Sensing" (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | IR Capture
|
|
Hi handyboarders! I'm currently controlling my camcorder pan (left-right) and tilt (up-down). My camera is a Nikon VN-310. I have a small (very small!) remote control to make it zoom, record, play, stop, etc. Now the thing is I want to use those (...) (29 years ago, 2-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Capture
|
|
(...) Try my IR routines available at (URL) should handle any # of data bits and any kinds of codes. e-mail me personally if you need more help. /Max (29 years ago, 3-Aug-97, to lugnet.robotics.handyboard)
|