 | | Re: Short term memory ablut sensor input???
|
|
(...) The program doesn't actually record in the Vectors array any information about where it saw an obstacle. It just records which direction the robot went and how far (according to the rotation sensor) during the last leg of the journey. Each (...) (26 years ago, 22-Sep-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Lego Mindstorms in Swedish television
|
|
(...) Or for every one, here is the official page from the University: (URL) and drool :) TGIF! /Tobbe (26 years ago, 22-Sep-00, to lugnet.loc.se, lugnet.general, lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Possible error in assembly guide.
|
|
Are you getting a good ground???...??? If it works.. then hey! RS232 is +10 to -10 but there is room for slop! +7 to -7 will work too!!!!!!! It just won't drive a cable to the max length of the RS232 spec. Most of the time though people just don't (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
 | | Possible error in assembly guide.
|
|
Near the end of the "interface/charger serial circuit" heading of the "Assembling The Handy Board" guide, it says measure the voltage of pin 6 of the MAX232, I did that and got -9.5 which is correct. Then I connected pin2 of j9 and pin6 of max232 so (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Remote control
|
|
I have successfully trained my Sony Integrated Remote Commander RM-AV2000 (retails for $120) with the $20 remote from Lego. I have not tested training the remote from the IR tower, but I'm sure it would work. I'm also sure you could train any (...) (26 years ago, 22-Sep-00, to lugnet.robotics)
|
| |
 | | RE: Remote control
|
|
(...) Hey good idea... Now I can justify a fancy learning universal remote to myself! m@ (26 years ago, 22-Sep-00, to lugnet.robotics)
|
| |
 | | Remote control
|
|
Has any one tried using a universal remote on the RCX to see if it would work? If it did, $5 is a great improvement over $20! (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Strong gear assemble?
|
|
Thanks for the help! After sending out the email, I thought of a way to do it (using a worm and a 40t gear ;), so now it lifts its self. Its interesting to watch as it rises though, because even though its semetricle, it goes up on first one leg, (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Strong gear assemble?
|
|
I second the turntable suggestion. Triple black pin two beams to the molded-in mounting lugs and you can make a perfect space to worm-gear the outer ring. As an added bonus you get tons of mounting surface to put the rest of your big- rig (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Advice on Rotation sensors and steering please.
|
|
Sorry. No I meant with correcting. My motors were matched pretty well, but without correction there was a large 2-3 foot error. Also the 500->15ft statement was an approximation of the actual numbers, I did this 3 months ago. Andy (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Short term memory ablut sensor input???
|
|
Can you remember a touch sensor reading? This way by using only one light sensor as an irpd, I can detect which way to turn to avoid the obstacle. (...) */ (...) turning */ (...) */ (...) travel */ (...) */ (...) ------ (...) */ (...) ------ (...) (...) (26 years ago, 21-Sep-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Strong gear assemble?
|
|
(...) combination (...) (assuming (...) If you have a turntable around, you can do even better than that. I never counted how many teeth it has on the outside, but it's a lot more than the 40t gear. And even better, it has molded on "mini-beams" to (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Strong gear assemble?
|
|
If you are having trouble with the weight of the object ( robot) that you are lifting, you could possibly work a worm gear into the gear box. The worm gear changes the direction of motion, which prevents the weight of the object from working (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Strong gear assemble?
|
|
I believe the weakest points are the axles. They twist and bend easily. At points where you have to transfer the largest forces, make sure you don't have long axle sections between the wheels. Keep the wheels next to each other if possible. If you (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | RE: Strong gear assemble?
|
|
A worm gear mounted against a 40t gear is, I believe, the 2-gear combination that provides the most torque. You may want to gear down the worm gear first, providing even more torque. In general, as speed decreases (assuming the decrease is caused by (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Strong gear assemble?
|
|
What is the strongest gear assebly? Using mostly RIS 1.5 pieces, but some extras, I need to design a gear box that has enough strength to lift the contraptions own weight. What is the strongest possible settup of gears that i could use to achieve (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | C++ support in CVS
|
|
Hey, everyone- Thanks to the patches Pat Welsh posted last week, C++ support is now in the CVS version of legOS. Pat made a number of changes to clean up the makefiles, so everything will compile if you aren't using gcc 2.95 and/or don't plan to use (...) (26 years ago, 21-Sep-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Advice on Rotation sensors and steering please.
|
|
I discovered, during the course of implementing a software interface to the Lego rotation sensors on another hardware platform altogether (not RCX) that there is a problem with the sensors themselves. They suffer from the well known "between states" (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
|
| |
 | | Re: nimh batteries
|
|
the issue with nimh is that plain trickle charge is not appropriate. you must remove charge current when the cells are full charge. the HB charge circuit just doesn't do that. i'd really recommend switching back to nicad. fred In your message you (...) (26 years ago, 21-Sep-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Lego bulk
|
|
(...) [snip] (...) Check out (URL). (26 years ago, 21-Sep-00, to lugnet.robotics)
|