 | | Re: External supply for RCX
|
|
(...) No one has answered your Question fully so here goes. The RCX with the power Adapter port is the 'old' one. It's power port can take the following: AC or DC (It doesn't matter what direction) AC is a little easier on the RCX as it uses both (...) (26 years ago, 2-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Info request
|
|
Take a look at the original reverse engineering of the RCX at (URL) best site for the internals of the RCX with pictures.... Ram PS: You could probably just use wireless serial radio modems for this! It works as follows: PC--->serial (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Vision Command in Nederland
|
|
Is Vision Command te koop in Nederland? Zo ja, waar? Does anybody know whether Vision Command is sold in the Netherlands? If yes, where? Harrie de Leeuw Eindhoven The Netherlands (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Info request
|
|
Ok, enough's enough! I'm going to take a crack at the IR - RF link thing for the RCX. I'm not promising it's going to be pretty (or cheap) though! But I'll try. First of all, a question - Does anybody know if the schematics for the RCX and more (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) Yes - but alkaline batteries drop gradually in voltage throughout their lives - by the time they run out, their volts are below 1.2. NiCd's on the other hand stay at 1.2 volts and dry up much more suddenly...over just seconds sometimes. Dunno (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) I've been using rechargable Eveready Renewals in one of my RCX's for quite a few months without any problems... I think it is the lower 1.2 volt compared to the 1.5V of a standard battery that they are concerned with. Dave (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: IR Ball (was Soccer-Playing Robots)
|
|
(...) That is right. It's not only a mere problem of area covering, but the main objective is to have the robot locate the ball quite quickly without a significative error. We tried at first with the same ball and less LEDs and it was working, but (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | RE: IR Ball (was Soccer-Playing Robots)
|
|
Thanks! I _do_ get into toy stores fairly often ... but generally ignore stuff at the register and normally go straight to the Lego aisle. :) Doug Wilcox Senior Web Developer iMcKesson Provider Solutions Group-Needham 160 Gould Street, Suite 130 (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | RE: IR Ball (was Soccer-Playing Robots)
|
|
I suspect (but am trying to confirm) that the high number of LEDs was not just to increase the area covered, but the luminosity as well. (Can one use the term _luminosity_ for IR if it's outside our visible spectrum?) The "brighter" the ball in IR (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: IR Ball (was Soccer-Playing Robots)
|
|
>That wouldn't look as great as a free rolling ball - and the >robots would perhaps have trouble finding it while it's in >motion....but 28 LEDs is a heck of a lot! Seems like a lot to me. The wider angle IR LEDs have a 60 degree cone. I think you (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: IR Ball (was Soccer-Playing Robots)
|
|
(...) Wander into any toy store and you'll find small figures (Pokemon's etc) packed into plastic spheres that split conveniently around the equator. You should have no problem finding one of an appropriate size there were LOTS to choose from at our (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | IR Ball (was Soccer-Playing Robots)
|
|
The Lego light sensors are particularly sensitive to infra-red (one of those gems of information that I've picked up from the robotic mailing list), so the standard Lego light sensors can be used to "see" a ball that's throwing off lots of IR, like (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) Speaking of batteries, the manual advises against using rechargeable ones. Does anyone have experience with that? Why not use them? (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) Actually, the 'new' one is the one without the adapter socket. Lego stopped putting them in, apparently to save a few cents on the cost of each RCX. :-( You can get 'official' Lego adapters from (URL) the link to the item (appologies for the (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
It's the 'older' RCX. The connector actually requires AC voltage at (I recall) 12V - I forget the amperage. (I've been using an old Panasonic answering machine psu that's 13v @ 500mA for 10months now with no problems.) -Simon "Jan Nouza" (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Vision Command and Linux?
|
|
Does anybody know whether the Vision Command Camera works with Linux? Jürgen (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | External supply for RCX
|
|
Hi, recently I purchased a LEGO Dacta Robotics set containing a RCX. To my surprise, the RCX was different from that I purchased with RIS 1.5 a month ago. The 'new' one has a socket for an external voltage supply (as I can guess from the '9-12 V' (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Temporary solution for W2000, but not Notebook
|
|
Hi, I am assisting a Robotics course with the venerable HandyBoard, and have been having the same problem with the Toshiba, and ThinkPad laptops. With Toshiba though, there is no infrared as far as I can tell, and I can run and load the inital pcode (...) (26 years ago, 1-Sep-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Limited slip differential
|
|
I thought you were a native English speaker :) One question I have: how to you engage and disenage the lock? Is this automatic? Is the mechanism more mechanical or more electronic? -Brian (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Servo.c
|
|
Hi. I´m using the servo_a7.icb file to drive a servo on my handyboard, but the servo is not moving. it seems that the frequentcy is not the right one (40hz). And I was looking for the servo.c file, because it seem easy to use, but i can´t find it. (...) (26 years ago, 30-Aug-00, to lugnet.robotics.handyboard)
|