To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22144 (-10)
  Re: DACTA PARTS QUESTIONS
 
(...) That's not a sensor, but an adapter. It allows you to connect DPC sensors to the RCX. Here's a description from (URL) : --- This adapter allows you to connect DCP's range of sensors directly to the RCX. Using the ROBOLAB Investigator software, (...) (26 years ago, 6-Jun-00, to lugnet.robotics)
 
  RE: fast computer problems
 
Still no luck! any other ideas ??? - what baud rate is the port meant to be set at? 9600? Thanks again Ross -----Original Message----- From: Gary Livick [mailto:glivick@pacbell.net] Sent: 05 June 2000 08:25 To: The Glashans Cc: (...) (26 years ago, 6-Jun-00, to lugnet.robotics.handyboard)
 
  Re: where do I download lnpd+liblnp?
 
(...) ---...--- "Going to California with an aching in my heart. Someone told me there's a girl out there with love in her eyes and flowers in her hair." -Led Zeppelin, "Going to California" ---...--- (26 years ago, 6-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: rcx+hp48gx
 
(...) header, (...) Check this web page: (URL) has the IR communications spec for the RCX brick. Look down the page for the "Communications" section. have fun, DLC (26 years ago, 6-Jun-00, to lugnet.robotics.palm)
 
  where do I download lnpd+liblnp?
 
I can't seem to find anywhere to download the lnpd+liblnp tar ball. Does anyone know where it might be? Torkel (26 years ago, 6-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: Servo motors & RCX
 
It seems to me that Ralph Hempel has a servo driver for pbFORTH. I seem to recall him polling for interest in a more general RCX solution. (...) -- ___...___ And Jesus said to them, "Come with me, and I will make you fishers of men." At once they (...) (26 years ago, 6-Jun-00, to lugnet.robotics)
 
  DACTA PARTS QUESTIONS
 
I just got a dacta catalouge, I have quick questions: 1. What is the 9917 DPC Sensor? 2. What is the difference between the "standard" touch sensor & the 9888 Each of these may be seen at: (URL) A (26 years ago, 6-Jun-00, to lugnet.robotics)
 
  Re: 0.5 degree resolution with rotation sensor
 
I don't really need it to be really precise, because, yes, the gear train is a huge factor in a situation like that. I only built the gear train and I'm using another rotation sensor as the reference for my controller. Depending on the position I (...) (26 years ago, 5-Jun-00, to lugnet.robotics)
 
  SCI, IC and interrupts
 
Hi I need to communicate with my handy board using the serial port using the Interrupt for SCI. I tried to test several programs that I found, without success. My basic test is the following. 1.- I created and .asm file which is a copy of the (...) (26 years ago, 5-Jun-00, to lugnet.robotics.handyboard)
 
  Re: fast computer problems
 
What works on my computer is to go into the port settings, set XON-XOFF, and then enable the FIFO buffer and turn the speeds all the way up. I have a Toshiba laptop, so hopefully your settings will be the same. If I do it any other way under WIN98, (...) (26 years ago, 5-Jun-00, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR