 | | buying Chips
|
|
Anyone know where to get a hold of one 6811 microprocessor for around $10? Everything I've seen sofar either wants you to buy in bulk (you have to buy 23 @ $7.11 from Motorolla) or almost $20 for 1 chip. This stinks! Any info would be appreciated. (...) (29 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Handy Board Problem: getting hb back into download mode
|
|
(...) Are you holding down the STOP button? With the board powered on, read the voltage at pin 3 of the 6811. When pressing the STOP button, pin 3 should read between zero volts and 0.6v. Releasing the STOP button, you should get 5v. If you get 5v (...) (29 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | HOW TO UNSUBSCRIBE
|
|
Greetings, This is the periodic message about unsubscribing. Please DO NOT send unsubscribe messages to the whole list. To unsubscribe, send email to fredm@media.mit.edu. Regards, Fred (29 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Handy Board Problem: getting hb back into download mode
|
|
Hello, I'm at a loss for what will take to get either of the two boards into DL mode. The board has nothing plugged into it; the BATT and PWR LEDs flash on and then PWR remains on so I can not confirm the synptoms of the ds1233(U12) voltage monitor (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Unsubscribe
|
|
unsubscribe Have compassion on those who live on earth and He who is in heaven will have compassion on you. God will show no compassion to him who has no compassion towards all mankind Prophet Muhammad (P.B.U.H.) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: your mail
|
|
(...) Get your soldering iron, some solder labeled electronics use, some old circuit board, and solder away. Or, you could take an old computer board and desolder some components from it, and re-solder them in. Just get in there and do it. You know (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Vector 2x compass
|
|
A mistake has been found on the V2X schematic, the M/S pin on the compass needs to be grounded. I don't know what it is, everytime I publish something, I make a mistake. (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Strange HB problems
|
|
Over the past two days I have had two problems with my HB that I can't explain. Maybe you you can help. 1. I wrote a simple program to test out my motors that consists of the motor, sleep, and beep commands. Once in a while I get an error back while (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Another note on soldering.. Heat control is VERY important.. Not so much being able to adjust the heat, as having a temperature-controlled iron. The "cheaper" irons get hotter or colder with the load (speed of soldering) as well as the room (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Soldering (fwd)
|
|
Often novices miss the single most fundamental point about soldering: you don't use the iron to melt the solder (99% of the time) -- you heat the component leads and let them melt the solder. To initially transfer heat effectively to the leads, a (...) (30 years ago, 18-May-97, to lugnet.robotics.handyboard)
|