To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1506 (+10)
  Re: Motors & handyboard
 
(...) This is also excellent advice. On one R/C car I had, I ended up having to simulate the signal input to the controller because the h-bridge was so screwy but it does save you from having to build your own. On a related note, Radio Shack sells (...) (30 years ago, 19-Feb-97, to lugnet.robotics.handyboard)
 
  Digit outputs....
 
I've tried to program the digital outputs from the SPI header J6 on the HB with no success. I pump the values into the HB as per instruction form the FAQ note and measure the 4 outputs. No high/low, just some sort of oscillation. What could be my (...) (30 years ago, 20-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Digit outputs....
 
Rather than trying to figure out the hex for the bits, I use the IC binaray number format, "0b". I set the bits using a binary mask, for example, to set the MOSI pin high, I use: bit_set(0x1008, 0b00001000) then to set the MOSI pin low, I use: (...) (30 years ago, 20-Feb-97, to lugnet.robotics.handyboard)
 
  SPI Routines in IC
 
Anybody have any routines or know of any published information for using the SPI with IC for: ...use with Dallas Semi's serial real time clock - DS1202 ...use with 12 Bit serial A/D - LT1298 ...use with Dallas semi's Thermomerter - DS1620 Thanks a (...) (30 years ago, 21-Feb-97, to lugnet.robotics.handyboard)
 
  motor drivers
 
Hi all, I am running some motors from a Mini Board and I want to up the current output of the board. I have noticed that the motor drivers on the MB are the L293 chips just like the Handy Board. Now if the 1 Amp motor chips that many Handy Board (...) (30 years ago, 21-Feb-97, to lugnet.robotics.handyboard)
 
  Re: motor drivers
 
David, You can replace the L293 on your MiniBoard with the TI SN754410 with no adverse effects. The two chips are pin-for-pin compatible. - Prabal (...) (30 years ago, 22-Feb-97, to lugnet.robotics.handyboard)
 
  IR collision avoidance
 
Howdy, Is there anyone out there that can explain programming IC for IR collision avoidance. I have read the mobile robots book and everything in the IC manual I downloaded and the 6.270 hardware info but still haven't got a good grasp of the best (...) (30 years ago, 22-Feb-97, to lugnet.robotics.handyboard)
 
  Re: motor voltages
 
I (...) Use a couple power diodes in series with the motor power supply, _NOT_ the motor itself. You'll need pretty heafty diodes if you go this route. A typical Si diode drops between 0.6 and 0.7 volts when forward biased. String a few together and (...) (30 years ago, 23-Feb-97, to lugnet.robotics.handyboard)
 
  motor voltages
 
Hello again, Thanks to all who responded to my query regarding motor chips on the Mini Board. Now that I have the more capable motor drivers installed, I want to lower the voltage that my motors see. They are getting straight 9V from the motor chips (...) (30 years ago, 23-Feb-97, to lugnet.robotics.handyboard)
 
  Re: IR collision avoidance
 
(...) I'm sending this to other members of our robotics team because we JUST mastered wall-hugging IR this week. They may have other things to add. (...) Here's the pseudo code: Start Any bumpers hit? YES - Execute the back up, turn 90 degrees left (...) (30 years ago, 23-Feb-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR