 | | Re: Linux for the HandyBoard
|
|
No there is not. --Chuck (...) (27 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Piano Player
|
|
I was inspired by Mario's piano player and conductor and decided that I had to build one. I built a robot that can play my daughter's "Little Tykes" piano. It currently plays mary had a little lamb. You can see some pics at: (URL) Shafer (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Piano Player
|
|
(...) I'm glad my work inspired such a nice creature! Mario (URL) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Linux for the HandyBoard
|
|
thanks I maily wanted it for building a cheap, viable Linux platform without having to delve into a somewhat-costly PC/104 board or the like... does anyone know of a cheap pc/104 or other small 486-based board available? thanks, --phil -----Original (...) (27 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Power Supply
|
|
(...) down (...) Hi, Yes - should be OK - power connector disconnects the batteries when an external PSU plugged in (assuming the plug fits the RCX properly!). I guess there is a small risk of the firmware getting erased when plugging in/out the (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Power Supply
|
|
Kevin Baker <kevin.baker@racalitsec.com> wrote in message news:FHFJEF.7K2@lugnet.com... (...) I think the RCX uses the supply with the highest voltage. It doesn't actually disconnect the batteries. If it did, the RCX would go dead when you unplug (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Handy Board software
|
|
take a look at Ray's Robotic Computer. i have a url somewhere. This dude makes a 68HC11 mini board in modules from his basement. Completely assembled and tested versions too. I found him through altavista a couple of times +breiler (...) (27 years ago, 2-Sep-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
|
| |
 | | Re: robotic rovers
|
|
I had written: (...) Yeah, I suppose you are right. I think the only advantage to this scheme is that you can use a micro motor to power the clutch mechanism to that you don't tie up a full size motor. Also if you are running out of motor outputs, (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | 2 IN 1
|
|
(...) (27 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Tachometer re-posted
|
|
This is a re-post of the thread called "Poor man's Tachometer" for the WEB interface users. Brian Alano pointed out that the web interface of LUGNET does not accept or even show posts with attachments. He liked the design so much he decided to add (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Power Supply
|
|
Yes, you can program and run the RCX from a Wall Wart with the batteries in it. It will keep the programs that were downloaded when the Wall Wart is unplugged from the RCX. I use this method all the time to save batteries while programming and (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Power Supply
|
|
(...) If I remember correclty, the RCX will keep its programming for a few seconds after the batteries are removed, this allows you to change the batteries without having to reprogram. So it could disconect the batteries or at least isolate them (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | Re: Linux for the HandyBoard
|
|
A 486 Board + 486 + 4Meg of ram + 100 Meg drive + keyboard should cost around $20. Or free if you go dig in the right trash ;^). I don't know where you are but around here (San Francisco Bay area) shops like Weirdstuff ((URL) are selling used (...) (27 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Any have a BS11 there willing to part with?
|
|
Hi I know this is'nt a HB ques , but , Does anyone have a BS11 that theyed be willing to part with , or know somewere they can be uptained relitvely CHEAP Thanx -- Alex (27 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Droid Developer Kit, Robotics Discovery Set
|
|
The Star Wars Droid Developer Kits and Robotics Discovery Sets are IN STOCK NOW!... we've got a few hundred of each. Jason Cooper - robotman@slip.net (...) (27 years ago, 2-Sep-99, to lugnet.robotics)
|
| |
 | | RE: Handy Board software
|
|
The URL appears to be: (URL) Michael -----Original Message----- From: mibm@image.dk [SMTP:mibm@image.dk] Sent: Thursday, September 02, 1999 4:16 PM To: lego-robotics@crynwr.com Subject: Re: Handy Board software take a look at Ray's Robotic Computer. (...) (27 years ago, 3-Sep-99, to lugnet.robotics)
|
| |
 | | SOLDER
|
|
WHAT'S THE BEST "SIZE" SOLDER TO USE WHEN SOLDERING A 28 GAUGE WIRE (MOTORS AND SENSORS) TO A MALE PIN! (27 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Linux for the HandyBoard
|
|
thanks I maily wanted it for building a cheap, viable Linux platform without having to delve into a somewhat-costly PC/104 board or the like... does anyone know of a cheap pc/104 or other small 486-based board available? thanks, --phil Phil: Check (...) (27 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: SOLDER
|
|
Hi, I tend to use 22 SWG multi core solder for all my soldering jobs, and find it works for me. Russ.. -----Original Message----- From: Paul DaCosta [mailto:germano@voicenet.com] Sent: Friday, September 03, 1999 2:01 PM To: Handyboard Subject: (...) (27 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | decoding a message sent by an RCX
|
|
hiya, I have been working on an idea to extend the number and type of devices that the RCX can control. I started with the idea of encoding serial data on one of the motor lines and decoding that in a PIC to do <stuff>. However, because working at (...) (27 years ago, 3-Sep-99, to lugnet.robotics.rcx.nqc)
|