 | | a correction! to r/c servo
|
|
Sorry about that! The resulting 0.03 mS pulse width increments would result in 5 degree increments in the position of the servo shaft. How about that? JB -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Re: r/c servos
|
|
(...) I think what John was trying to say was that pulse widths between 0.7 ms and 2.0 ms give servo rotations between 0 and 180 degrees. With 45 steps in that range, you can control the servo in 5 degree increments. Seems to me he was approximating (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Re: r/c servos
|
|
okay.. how about this.. avg servo needs.. 60hz pulses.. 1.0ms pulse width = end point 1.5ms pulse width = middle of rotation 2.0ms pulse width = other end point that is the form of the data to the servo. so you need to out put pulses 60 times a (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Re: r/c servos
|
|
(...) That doesn't make sense either. If a single step of 2.0 ms causes 180 degrees of rotation, then how does 45 steps allow you to control it 5 degrees at a time? (...) Are you saying that the servo actually operates in steps of one degree each? (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | RE: r/c servos and firmware
|
|
Ok, Here's my 2 cents on servos...read to the bottom if you are interested in helping to develop the code for this. The servo takes a 60Hz (approx) pulse width signal between 1 and 2 msec The pulses are fed into a little circuit that generates an (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | RE: r/c servos and firmware
|
|
(...) OhOh, I've piqued my own interest. I've looked at the H8 hardware manual and the RCX internals. The OC1A triggers every msec, except the stupid routine clears the Free Running Timer every time!!!! So much for using the OC1B, maybe. The minimal (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Re: r/c servos and firmware
|
|
(...) Okay! Finally I got it! (-: It sounds to me like servos can't rotate continuously in the same direction. In other words, they're good for steering but not for turning the wheels that make the car go. Is that right? Anyway, having heard that (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | RE: r/c servos and firmware
|
|
(...) There are multiturn servos for winches in RC sailboats, but they are REALLY expensive. (...) Well don't give up too fast. They ARE useful for steering, or lifting, or grabbing because we can set the limits of motion. This makes things like (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Using RCX with Lego Trains
|
|
I just picked up the Lego "Railway Express" set (#4561) last night. It comes with a "Toy Transformer" electrical plug (adaptor). The label on the plug says (North American version): Input: 120 VAC 60 Hz 0.12 A Output: 12 VAC 7 VA Would this work as (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|
| |
 | | Re: r/c servos and firmware
|
|
(...) Almost exactly how I'd do it. The problem is what if OCIB must be set to a small value, and the FRT has already passed this value when the OCIA handler sets up OCIB in step 3? This problem is solvable. If the total interval is closer to 1 ms, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
|