To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *13361 (+10)
  Building help from TLG
 
I just discovered this hidden gem in the DACTA Robolab site: (URL) step by step instructions for a couple of useful gizmos. Karen (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Re: The new Super Car
 
(...) I was in error regarding the use of element mr0079 (3x3 Throwbot foot) in 8445 Indy Storm. I've looked at the pictures again and can't see the part where I thought it was. However, it is definitely used in 8448 Street Sensation (the red "new (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  RE: Gripper and lift arm with single motor
 
Yes would appreciate some pics I tried this approach but ended up with all kinds of problems as you suggest -Exploding Lego ! Thanks David Walton Email: d.walton@ndirect.co.uk Take a look at my homepage (still under construction though) (URL) on (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  RE: Building help from TLG
 
(...) Yes it is a decent site, too bad they can't spell vertical properly :-) Ok, beef mode on...There's a really neat page in the Constructopedia section of the site that has a grabber sub-unit. There has been a lot of discussion on grabbers (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Re: Not that you care...
 
(...) This isn't exactly the type of adaptive mapping you're talking about, but it will give you an idea of the complexity of the task. Go to: (URL) and read the sections on "occupancy maps" and "localization". (...) Right. No persistent variables (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Club San Franlego
 
browsing around the "Lego Robotics Laboratory" web site (URL) I came across a link for the Club San Franlego, one can only assume that this is a club for lego fans in San Francisco and since this is my home town I would be very interested in (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Re: Droid Developer Kit is here
 
(...) What you're actually trying to say, is that the light sensor would generate a pulse each revolution, not each minute. The RCX has to measure the minutes internally, the light sensor would measure the revolutions. You could also have the light (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Micro Scout light sensor (was Re: Droid Developer Kit is here
 
(...) Most "light sensors" are sensitive to the light put out by IR remote controls and other devices with standard IR-emitting diodes. It's actually more expensive to make a light sensor that does *not* pick up IR wavelengths. Therefore, it's (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  Re: Building help from TLG
 
----- Original Message ----- From: Ralph Hempel <rhempel@bmts.com> To: <lego-robotics@crynwr.com> Sent: Tuesday, August 10, 1999 11:26 AM Subject: RE: Building help from TLG (...) frame? Two ways: 1) Right click on the frame that you want the URL (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
 
  IR-Tower and PowerBook-G3 ?
 
Has anyone else had problems using the IR-Tower with a PowerBook-G3 (WallStreet '98)? I tried for two days and only got 'Problem talking to IR device' messages. Tried different cables, cont-checked both cables. Finally went and tried it on the GFs (...) (27 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR