To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1261 (+10)
  RE: LM629 and "quadriture incremental" encoders
 
The last time I priced these chips they were $249.00 each qty 1. (a bit expensive for my robots, but I've used them and they are cool) --Chuck ---...--- From: James Lewis[SMTP:jlewis@nomadics.com] Sent: Wednesday, January 15, 1997 5:10 PM To: (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: unsubscribe
 
Please unsubscribe "vie100@psu.edu" from the mailing list. (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: dual servos
 
There may be two separable issues in your experiment: 1. "twitching" when the control value isn't changing. this should not happen. 2. twitching because of flakiness in the pot reading. this would not surprise me at all. if the A to D reading on the (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: IR wall detection
 
Keith, Try an LM567. It's a tone decoder with PLL and VCO. Basically set the internal freq. of the 567 any where between .01 Hz up to I think 500 kHz. Feed a signal into the 567 and if the freq's match up, the 567's output goes low. I've been (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: LM629 and "quadriture incremental" encoders
 
James, That's probalby my post you read. I'm still working on hooking 'em up. I'm gonna use two 629's and two 18200 H-bridges. The 629 uses encoders simmilar to the ones in mobile robots. The quadrature encoder has two signals that are 90 degrees (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  100 sensors
 
I am interested in sensing with about 100 water activated switches and am wondering if this is at all possible with the Handy Board.I had thought that it might be possible to by making them all return different levels of current at the sensor input (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: IR wall detection
 
(...) Keith I think it works. I managed to get a bread boarded version of the IR sensor working. A 555 provides a 40khz carrier. The 555's reset pin is directly tied to pin 5 of a 567. The carrier is modulated by the internal freq of the 567. A (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  Re: 100 sensors
 
Joe, A very handy way to connect lots of digital switches is to arrange them in a resistor ladder and connect them into an analog input. You could get up to 8 switches into one input, giving you 256 different voltage levels, in theory, but in (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  step motor interface & control
 
For anyone interested in using step motors: I have found a way to use them - Pull out the L293's chips, replace the y6 clk signal on the motor latch with y4, then pokes to 0x6fff will allow you to send bit patterns for 2 unipolar 5 or 6 wire (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)
 
  power and servo
 
Hi everyone, I've got two problems that I hope your combined expertise can solve. 1) I cut the trace connecting the the motors to the main board supply, so that I could power them independently (as per the instructions I found on the web). The board (...) (30 years ago, 16-Jan-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR